The Tefal Pure Air PT3030/PT3040 is an air purifier designed for domestic use, aiming to provide cleaner indoor air and protect health through a multi-level filtration system.
Function Description:
The primary function of the Tefal Pure Air is to filter pollutants from indoor air. It utilizes a series of filters to trap various contaminants, ensuring a healthier breathing environment. The device operates with up to 3 filtration levels for the PT3030 model and 4 filtration levels for the PT3040 model. Each filter level is crucial for targeting specific pollutants.
Important Technical Specifications:
The device features several control buttons and indicators on its control panel (B).
- Main Unit Components:
- A: Air outlet
- B: Control panel
- C: Front panel
- D: Rear panel
- E: Sensor cover
- F: Air inlet
- G: Mains cable
- Control Buttons:
- 1: On/off button (to turn the air purifier on/off)
- 2: Mode button (to select one of four modes: Daytime auto, Nighttime auto, Quiet, Turbo)
- 3: Timer/child lock (to enable/disable the timer or child lock)
- 4: Brightness/reset filter button (to set brightness or reset filter settings)
- Indicators:
- 5: Child lock indicator
- 6: Timer Indicator
- 7: Replace filter indicator
- 8: Day time Auto mode indicator
- 9: Night time Auto mode indicator
- 10: Quiet mode indicator
- 11: Turbo mode indicator
- 12: Air quality indicator (located on the front panel (C), changing color to indicate air quality level: Blue for Excellent, Purple for Average, Red for Poor)
- Filtration System:
- Pre-filter: Traps large particles like dust, hairs, and pet hairs. This filter is reusable and can be cleaned with a vacuum cleaner or rinsed with water.
- 2in1 Active Carbon & Allergy+ Filter (XD6230): Targets smoke, unpleasant odors, chemical pollutants, Volatile Organic Compounds (VOC), allergens, pollen, dust mites, germs, molds, bacteria, and viruses. This filter cannot be cleaned or reused and must be replaced.
- NanoCaptur+ filter (XD6082) (only for PT3040 model): Specifically designed to capture formaldehyde. This filter changes color to indicate saturation and needs replacement when its granules become opaque white or crumbly, or every 12 months if not saturated.
- Power Supply: The appliance complies with low voltage, electromagnetic compatibility, and environmental directives. It can operate using an unearthed plug and is a class II (double electrical insulation) device.
- Environmental Conditions: Recommended for use in ambient conditions lower than 35°C and 70% RH.
Usage Features:
- Installation: Place the purifier on a flat, stable surface in the room requiring treatment. Ensure at least 50 cm of free space on each side for proper air circulation. Avoid placing it behind curtains, under windows, or near furniture/shelves.
- First Use: Before initial use, remove all plastic packaging protecting the filters. Verify that the appliance's voltage, frequency, and power match your electrical supply. Ensure the appliance is fully assembled, placed on a stable surface, and air inlets/outlets are unobstructed.
- Operation Modes:
- Daytime Auto Mode: Fan speed is set to 2 or 3.
- Nighttime Auto Mode: Fan speed is set to 1 or 2.
- Quiet Mode: Minimum fan speed, ideal for quiet environments.
- Turbo Mode: Maximum fan speed, recommended when air quality is poor.
- Timer Function: Allows enabling or disabling a timer for operation.
- Child Lock: Can be enabled/disabled by pressing the timer/child lock button for 3 seconds.
- Brightness Control: Adjusts the brightness of the indicators.
- Filter Reset: After replacing a filter, press the brightness/reset filter button for 3 seconds to reset the filter settings. A force reset can also be performed if a filter is replaced before its lifespan ends.
- Air Quality Indication: The air quality indicator (12) visually communicates the current air quality (Blue for Excellent, Purple for Average, Red for Poor).
Maintenance Features:
- General Cleaning: Before any maintenance, switch off and unplug the air purifier. Clean the surface with a damp cloth. Do not use abrasive materials.
- Pre-filter Cleaning: The pre-filter should be cleaned every 2 months. It can be cleaned with a vacuum cleaner or rinsed with water. Ensure it is completely dry before reinstallation.
- 2in1 Active Carbon & Allergy+ Filter Replacement: This filter needs to be replaced every 12 months. It cannot be cleaned or reused.
- NanoCaptur+ Filter Replacement (PT3040 only): This filter needs to be replaced when its color changes (indicating saturation) or every 12 months if no saturation occurs.
- Pollution Sensor Cleaning: The particle sensor requires regular cleaning (every 2 months). Before cleaning, switch off and unplug the appliance. Clean the air inlet and outlet with a soft brush or cloth. Open the sensor cover, lightly wet a cotton swab to remove dust from the lens and inlet/outlet, then wipe with a dry cotton swab. Clean the sensor with a soft brush or vacuum cleaner. Do not use detergents or metal objects for sensor cleaning.
- Filter Handling Tips: When changing filters, especially if suffering from allergies or asthma, avoid direct contact with used filters. Wear gloves or wash hands thoroughly afterward. Place used filters directly into a closed, airtight bag to prevent spreading pollutants.
- Storage: When not in use, store the appliance in a cool, dry place with ambient conditions no higher than 35°C and 70% RH.
The Tefal Pure Air is designed to be user-friendly and effective in improving indoor air quality, with clear indicators and straightforward maintenance procedures.
Need help?
General
To Next Page
