TEK PARTNER™
UNIVERSAL REMOTE CONTROL
USER’S MANUAL
Contents:
HOW TO INSTALL THE BATTERIES
MAIN F EATURES
SETTING UP YOUR TEKPARTNER
SETUP BY ENTERI NG DEVICE CODE
SEARCH THROUGH THE LIBRARY
OPERATING THE TEKPARTNER
NORMAL OPERATION
MAINTENANCE
TROUBLESHOO TING
DEVICE CODE LIST
TV BRANDS
VCR BRA NDS
CABLE BOX BRANDS
Congratulations! Your T EK P ARTNER™ Universal Remote Control is a state-of-the-art device whic
integrates many different infra-red remote controls. T he TEK PARTNER™ is pre-programmed at the
factory, but you will need to enter a Device Code for each device to comple te the program. Sim ply
enter correct device codes for your equipment and your TEK PARTNER™ is ready to use! A Device
Code List is included in this User’s Manual. The TEK PARTNER™ replaces up to 4 separate remot e
controls to operate your infra-red controlled televisions (TVs), video cassette recorders (VCRs), and
cable boxes (CBLs).
HOW TO INSTALL THE BATTERIES
Your TEK PARTNER ™ requires 4 fresh AA-size batteries (alkaline batteries reco mmended).
1. Remove the battery cover on the back of your TEK PARTNER™.
2. Observe the polarity of the batteries and the "+/-" marks inside the b attery compartment.
3. Inse rt the batteries.
4. Push the battery cover back in place.NOTE:
When all batteries are disconnected, the TEK PARTNER™ retains its se tting only for 15 minutes.
Should yo u fa il to replace new batteries in time, use a stylus or the tip of a pen to reset the unit. Th
reset button is located inside the battery compartment.
You may now have to re-program your TEK PARTNER™. See SETTING UP YOUR TEK PARTNER™
section.
Page 1 of 7Tek Partner Universal Remote Control
3/10/03htt
.com/manual1.html
MAIN FEATURES
SETTING UP YOUR TEK PARTNER™
There are 4 Device Modes (TV, VCR, CBL, & AUX) in your TEK PARTNER™. You may setup the TEK
PARTNER™ by the following co de entering or searching instructions.
SetupbyenteringDEVICECODE
Referring to the DEVICE CODE L IST, look up the 3-digit DEVICE CODE which corresponds to the
brands and models of your video equipment. If there is more than one DEVICE CODE listed under
your brand, try the first code with the following instructions:
Forexample,enteringyourTV’scode:
1. Hold down "PREV CH" and "ENTER" together for approximately 4 seconds until the status indicat
(located to the left of the "1" button) lights up.
2. Press a desired Device Mode Button (e.g. "TV").
3. Use the number buttons t o enter you r 3-digit Device Code (from the Device Code List) for your
TV. The indicator should go o ut immediately. NOTE: The statu s i ndic ator will not blink while enterin
Device Codes in step 3 above.
4. Turn on your device (e.g. TV), try the functions on the TEK PARTNER™ . If your device (e.g. TV)
responds to your requested function correctly, you h ave entered the correct Device Code. Otherwis
repeat the a bove setup instructions with the remaining Device Codes until your device (e.g. TV)
responds to your requested function.
5. Simply repeat the above procedures to enter the Device Codes for your V CR & CBL - (Remember
to press a correct Device Mode Button in step 2 above).NOTES:
z
Any Device Codes c an be entered into "CBL" & "AUX" modes. (i.e. The "CBL" & "AUX" modes
can b e used to control TVs and/or VCRs). Simply press the "CBL" or "AUX" Device Mode
Button in step 2 above and ent er your 3-digit D evice Code for CBL or other devices.
z
If the indicator flashes twice during the above procedure, a wrong Device Code has been
entered. You are required to repeat steps 2 and 3 again.
z
If you canno t find a correct Device Code for your equipment, see Setup by SEARCH THROUG
THE LIBRARY section.
z
It is highly recomm ended, for future reference, to write down yo ur Device Codes on the
bottom label of your TEK PARTNER™.
SEARCH THROUGH THE LIBRARY
If you ca nnot identify a correct Device Code for your equipment from the Device Code List, you ma
try the code search method.
For example: T urn o n your device (e.g. TV).
1. Hold down "PREV CH" and "ENTER" together for approximately 4 seconds until the status indicat
lights up.
2. Press a desired Device Mode Button (e.g. "TV").
3. E nter a following corresponding Magic Search Code, and your TEK PARTNER™ is now ready t o
start searching.
Magic Search Codes: TV: 990 VCR: 992 CB L: 994
For example, press... ("PREV CH" & "ENTER" ... "TV" . .. 990)
To search: Aim your TEK PARTNER™ at the devic e (e.g. TV), press the "PWR" and
4. "VOL+" button alternately, repeatedly, slowly and patiently until the device turns off. (NOTE:
There are approximately 70 TV codes, 55 VCR codes, and 55 Cablebox
5. codes.) Once your device has been turned off, immediately press the same Device Mode Button
(e.g. TV) again to lock in the code and the indicator should go out. If the indicator flashes twice aft
pressing the "VOL+" B utton, you are already at the last code of the library. You may press "VOL-" t
search backward and repeat carefully the above procedures to search again. Simply repeat the
above procedures to search the Device Codes for your VCR and CBL keys. (Remember to press a
correct Device Mode Button in step 2 above).
NOTES:
Page 2 of 7Tek Partner Universal Remote Control
3/10/03htt
To Next Page
Need help?
General