Teknion KDH064B - User Manual

Http://www.czkaidi.com
- 1 -
KDH064B USER OPERATION INSTRUCTION
Read this instructions before operation
Digital Handset Operation
Picture
1. Initialization procedure
Step
Operation
Motion
1
Press and hold ▲&▼simultaneously
more than 6 seconds
Legs begin to move down at a half speed of normal operation
2
Keep pressing ▲&▼
Legs move down to the lowest position and rebound 2-5 mm, then stop
3
Release ▲&▼ together
Initialization is completed
The initialization procedure must be completed before the first running after table is installed or parts replaced
2. Move up and down
Step
Operation
Motion
1
Press and hold ▲
Legs move up
2
Release ▲
Legs stop
3
Press and hold ▼
Legs move down
4
Release ▼
Legs stop
3. Set memory positions 1/2/3
Step
Operation
Motion
1
Press and hold ▲ or ▼，then release
Run the legs to the position you want the table surface to be
2
Click button S, then click button 1 or 2 or 3
within next 3 seconds
Position 1 or 2 or 3 is saved
4. Move to the memorized positions
Step
Operation
Motion

Summary

Initialization Procedure

Perform Initial Setup

Guides the user through the mandatory initial setup process for the desk legs.

Desk Height Adjustment

Manual Up and Down Control

Instructions for operating the desk legs to move the table up or down manually.

Set and Recall Memory Positions

Explains how to save and return to preferred table height settings.

Move to Memorized Positions

Guides the user on how to activate saved height positions.

Handset Functionality

One Touch Key Function

Details enabling/disabling the one-touch feature for automated height changes.

Toggle Display Unit Format

Covers switching the height display between centimeters and inches.

Verify Display Data to Table Height

Guides users on checking and calibrating the displayed height against actual measurements.

Stroke Limit and Safety

Lock Bottom Stroke Limit

Instructions on setting a minimum height limit for the table legs.

Lock Top Stroke Limit

Instructions on setting a maximum height limit for the table legs.

Unlock Top;Bottom Stroke

How to remove previously set minimum or maximum height restrictions.

Adjust Anti-Collision Sensitivity

How to configure the sensitivity of the anti-collision system for safe operation.

Error Code Reference

Error Code Explanations

A list of error codes and their corresponding causes and recommended troubleshooting steps.

Troubleshooting Table Issues

No Response to Controls

Addresses problems where the desk controls do not respond to input.

Slow or Uneven Movement

Solutions for slow rising, one leg not moving, or uneven leg operation.

Unintended Movement

Deals with issues like legs moving down only or the table sliding down on its own.

Frequent Initialization

Explains troubleshooting steps when the desk repeatedly enters the initialization mode.

Overview

1. Function Description
2. Important Technical Specifications
3. Usage Features
4. Maintenance Features

This document describes the KDH064B Digital Handset, a user operation instruction manual for an adjustable table system. It details various functions, operational procedures, and troubleshooting steps.

Function Description

The KDH064B Digital Handset controls the movement and settings of an adjustable table. Its primary functions include:

• Initialization: Sets the table to its lowest position and rebounds slightly, completing the initial setup required after installation or part replacement.
• Up and Down Movement: Allows manual adjustment of the table's height.
• Memory Positions: Enables saving and recalling up to three specific height settings (1, 2, 3) for quick adjustment.
• One-Touch Key Function: A feature that can be turned on or off, likely for simplified operation of memory positions or other common actions.
• Display Unit Format Toggle: Switches the height display between centimeters and inches.
• Display Switch Data Verification: Allows users to verify and adjust the displayed height to match the actual measured height of the table, ensuring accuracy.
• Stroke Limit Locking: Users can set and lock both the bottom and top stroke limits, preventing the table from moving beyond desired minimum or maximum heights.
• Stroke Limit Unlocking: Releases the locked top or bottom stroke limits, allowing the table to move within its full range.
• Gyro Anti-Collision Sensitivity Adjustment: Configures the sensitivity of the anti-collision system, which detects obstacles and stops movement to prevent damage.

Important Technical Specifications

While specific numerical technical specifications like power consumption or motor type are not explicitly listed, the manual provides operational details that imply certain characteristics:

• Height Adjustment Increments: In inch format, the minimum height variation is 0.5 inches; in centimeter format, it is 1 centimeter.
• Memory Capacity: Stores 3 height positions.
• Overload Capacity: The table's load capacity is mentioned in troubleshooting, indicating that loads exceeding 75KG can cause issues like the table sliding down or frequent initialization.
• Anti-Collision Sensitivity Levels: The gyro anti-collision system has four sensitivity levels: G-0 (useless), G-1, G-2, G-3, and G-4 (highest sensitivity). The default setting after resetting is level 2 (G-2).

Usage Features

The KDH064B Digital Handset is designed for intuitive and user-friendly operation:

• Clear Display: Features a "Display Screen" that shows current height (e.g., "62.0"), unit (V for volts, though likely indicating unit format in this context), and status messages (e.g., "H-0", "H-1", "L", "-C-", "G-2").
• Dedicated Buttons: Includes UP, DOWN, S (Set/Select), and numbered memory buttons (1, 2, 3) for easy control.
• Combined Button Presses: Many functions are activated by pressing and holding combinations of buttons for specific durations, allowing for a compact interface.
• Initialization Requirement: The table must be initialized after installation or part replacement to ensure proper function. This involves pressing and holding UP and DOWN simultaneously for more than 6 seconds until the legs move to the lowest position and rebound.
• Memory Position Setting: To save a position, the user moves the table to the desired height, then presses and holds UP or DOWN, releases, clicks S, and then clicks the desired memory button (1, 2, or 3) within 3 seconds.
• One-Touch Key Activation/Deactivation: Pressing 'S' for more than 5 seconds, then releasing 'S' and pressing '1' within 3 seconds, allows toggling the one-touch key function. The screen displays "H-0" for off and "H-1" for on.
• Unit Format Switching: Pressing and holding 'S' and then 'DOWN' for about 3 seconds toggles the display between centimeters and inches.
• Stroke Limit Setting: To lock a bottom limit, the user moves the table to the desired lowest position, then presses and holds 'S' and '1' for about 3 seconds. "L" appears on the screen. A similar process with 'S' and '3' locks the top limit.
• Stroke Limit Unlocking: Pressing and holding 'S' and '2' for about 3 seconds unlocks both top and bottom limits, indicated by "-C-" on the screen.
• Anti-Collision Sensitivity Adjustment: Pressing and holding 'S' for about 5 seconds, then releasing 'S' and pressing '3' within 6 seconds, allows adjustment using UP or DOWN buttons.

Maintenance Features

The manual provides a comprehensive troubleshooting section to address common issues, which serves as a guide for basic maintenance and problem resolution:

• Error Codes: A list of error codes (E01 to E10) is provided, each with a description of the malfunction and suggested remedies.
  • E01 (Leg malfunction): Check cable connections, replace legs if inner parts are broken.
  • E03 (Table top overload): Remove excess load.
  • E04 (Control box malfunction): Re-initialization needed, especially after extreme environments or incomplete initialization.
  • E05 (Button of switch stuck): Check and toggle the button, or replace the switch.
  • E06 (Communication disconnected): Check connection between switch and control box, ensure control box works.
  • E07 (Lower setting of switch verifying height): Adjust height, lift the table if the setting is below 0.
  • E08 (Electrical short circuit): Check motor cable for damage, replace if necessary, power on again.
  • E09 (Abnormal HALL): Re-initialization can resolve this.
  • E10 (Drive anomalies): Cut power for 1 minute to cool the control box; if the fault persists, replace the control box.
• Troubleshooting Table: A dedicated section lists various fault phenomena and their corresponding handling steps.
  • No response after power connection: Re-initialize, check connections, contact supplier.
  • Legs rising slowly: Check input power, contact supplier.
  • Legs not moving as per operation: Contact supplier.
  • One leg moves, other doesn't: Check connection, contact supplier.
  • Legs only move down, not up: Re-initialize, contact supplier.
  • Table slides down itself: Check if load exceeds 75KG, contact supplier.
  • Frequent initialization: Check if load exceeds 75KG, check motor noise, contact supplier.

The manual emphasizes contacting the supplier for issues that cannot be resolved through the provided troubleshooting steps, indicating that deeper technical maintenance is typically handled by professionals. Regular checking of connections and ensuring the table is not overloaded are key user-level maintenance actions.

Teknion KDH064B Specifications

General

Brand	Teknion
Model	KDH064B
Category	Switch
Language	English