Tektronix 502A - Page 66

Parts List — Type 502A
RIGHT SIDE
REF.
NO.
PART
NO.
SERIAL NO.
Q
T
Y.
DESCRIPTION
EFF. DISC.
16.
337-256
1
SHIELD, V.A. chassis, alum. 3-'/ 4 x 5- 7 / 14 x ’ / 2 in.
211 -507
2
SCREW, 6-32 x 5 / 16 in. BHS
210-457
2
NUT, keps, steel, 6-32 x 5 / 16 in.
17. 179-395
1
CABLE harness, V.A. right
18.
348-003
2
GROMMET rubber, 5 / 16 in.
19.
337-007
4
SHIELD, tube, 7 / s in. ID x l- 3 / 4 in. high, with spring
20.
441 -494 1
CHASSIS, V.A. alum. % x 2-'/ e x 2- 7 / 8 x 6-'/ 14 in.
348-039
4
SHOCKMOUNT, assembly
406-399 4
BRACKET, shockmount, steel, ’ A x -875 x .531 in.
210-407 4
NUT, hex, brass, 6-32 x '/ 4 in.
210-006
4
LOCKWASHER, steel, internal #6
211-507 4
SCREW, 6-32 x 5 / 16 in. BHS
210-457
4
NUT, keps, steel, 6-32 x 5 / 16 in.
21.
343-042 2
CLAMP, cable, 5 / 16 in. (half) plastic
211-507 2
SCREW, 6-32 x 5 / 16 in. BHS
210-803 2
WASHER, steel, 6L x % in.
210-006 2
LOCKWASHER, steel, internal #6
210-407
2
NUT, hex, brass, 6-32 x ’ / 4 in.
22.
179-262 1 CABLE harness, Trigger
23.
179-782
1 CABLE harness, Position and Balance
24. 262-555
1
SWITCH, SENSITIVITY, wired
Includes:
406-401 1
BRACKET, front
406-402
1
BRACKET, rear
214-153 8 FASTENER, snap, double prong delrin
384-271 1 ROD, shaft '/ 8 in. dia. x 9- 5 / s in. long
376-014
1
COUPLING, pot, wire steel, .041 in. dia.
385-111
2
ROD, nylon, ’ / 4 x % in. tapped 5-40 in. thru
Mounting Hardware: (not included)
211 -507
2
SCREW, 6-32 x 5 / 16 in. BHS
210-803
4
WASHER, steel, 6L x % in.
25.
384-279
1 ROD, extension, switch assembly
354-201 1 RING, retaining
210-595
1
NUT, hex, alum. ’ / 4 -32 x '/ 2 in.
210-011 1 LOCKWASHER, steel, internal % in.
26.
200-263
1
COVER, dust, pot, vernier, poly, l7 / 32 xl in.
27. 384-545 1 ROD, spacing, alum. '/ 4 x 9-'/ 4 in.
28.
352-008 2
HOLDER, melamine, neon bulb, single, black molded
211-031
2 SCREW, 4-40 x 1 in. FHS
210-406 4
NUT, hex, brass, 4-40 x 3 / )6 in.
29. 210-202 1 LUG, solder, SE6 with 2 wire holes
211-538 1 SCREW, 6-32 x 5 / 16 in. FHS, 100° CSK, phillips
210-407 1 NUT, hex, brass, 6-32 x '/ 4 in.
30. 352-006
1 HOLDER, melamine, neon, double, molded
211-031
1 SCREW, 4-40 x 1 in. FHS
210-406 2
NUT, hex, brass, 4-40 x 3 / 16 in.
31.
211-023 2
SCREW, 4-40 x % in. FHS
210-406
4
NUT, hex, brass, 4-40 x 3 / 16 in.
6-10