TELECO AUTOMATION TVPRP868A01 User Manual

2
thetotalsecrecyofthecode.
-Thecodetransmissiontypeis“Rolling-code”.Thecodeischangedforevery
transmissionthroughtheuseofanalgorithmthatonlythereceiverisableto
recognize.
-InthereceivertheusercodeismemorisedunderEeprom,whichmaintainsthecode
informationevenwhenfacedwithblackouts(max.41code-memorisations).
Transmitters
Thetransmittersareencodedinthefactoryandeachtransmitterhasitsownunique
code.
Caution!Ifyoukeepachannelbuttonpresseddownformorethan30secondsthe
transmitterwillautomaticallyswitchoff.
ThereceiveriscompatiblewithalltransmittersoftheTVLinkrange:TVTXV,
TVTXP,TVTXC,TVTXK,TVTXQ,TVTXL,TVTXS.
To memorise codes from receiver
Mode 1
The memorisation or delete is made in the following way: channel 1 with channel
2 (or vice versa) and channel 3 with channel 4 (and vice versa)
Forsecurity,eachtimeyoucarryoutanewinstallation,youareadvisedtowipethe
entirememory(max.41differentcodes)
Theusercodeandtherelativechannelfunctionsarememorisedorcancelledviaradio
usingthefollowingprocedure:
1)PressandholddownP1,after0.8sthebuzzerB1willmake1bipandsound
continuously.
2)Transmitthechannelwhichistobememorised,thebuzzerB1willsound
intermittently.
Toinsertulteriorcodesrepeatpoints1and2.
Mode 2
The memorisation or delete is made in the following way: Single channels with
dynamic function, opening, stop, closing.
Forsecurity,eachtimeyoucarryoutanewinstallation,youareadvisedtowipethe
entirememory(max.41differentcodes)
Theusercodeandtherelativechannelfunctionsarememorisedorcancelledviaradio
usingthefollowingprocedure:
1)PressfortwotimesandholddownP1,after0.8sthebuzzerB1willmake2bip
andsoundcontinuously.
2)Transmitthechannelwhichistobememorised,thebuzzerB1willsound
intermittently.
Toinsertulteriorcodesrepeatpoints1and2.
To cancel a code from receiver: the delete happens in pairs like in the
memorisation mode 1 and 2:
1)PressandholddownthepushbuttonP2,after0.8sthebuzzerB1willswitchon
andsoundslowly.
2)Transmitthecodewhichistobecancelled,oncethechanneliscancelledthe
buzzerB1willsoundcontinuously.
Tocancelulteriorcodesrepeatpoints1and2.
To cancel all memorised codes:
1)PressandholddownP2foratleast0.8s,thebuzzerB1willsoundslowly,release
P2andpressitagainforatleast10s(duringthisperiodthebuzzerB1willsound
intermittentlyandquickly)asthebuzzerB1willsoundcontinuously.Releasethe
buttonaftercompletingtheoperation.
How to insert a transmitter via radio without accessing the receiver when the
memory is empty (rst installation), in this mode the channels function of the
transmitter will be in mode 1.
Thetransmittertobeinsertedwillbecomethemastertransmitterforinsertingother
transmitters.
1)PressP3ofthetransmitter,thereceiverwillactivatethememorisationandthe
buzzerwillsoundcontinuouslyfor5s.
2)Transmitthechannelwhichistobememorisedwithin5s.Oncethechannelis
memorisedthebuzzerwillsoundintermittently.
Attention:Whenmemoryisemptydonotgivepowertomorethanonereceiveratthe
sametime,becausetheabovementionedprocedureactivatesallreceivers.
How to insert a transmitter via radio without having to access the receiver by means
of an already memorized transmitter (memory indexing procedure)
Thetypeofmemorisationofthechannels(single,coupleor7-channel)dependsonhow
thechannel,whitchisusedinpoint2,hasbeenmemorized.
1)PressthebuttonP3locatedinsidethealreadymemorizedtransmitter.Theenabled
receiversoundcontinuouslyfor5seconds.
2)Transmitachannelpresentinthememoryofthereceiver,inwhichthenewcodeis
tobememorized,within5secondsandthebuzzerwillinterruptthesoundfor1sec,
andthencarryonforanother5seconds.
3)Transmitthenewchanneltobememorizedwithin5secondsandoncememorized
thebuzzerwillsoundintermittently.
Toinsertothertransmittersanothercoderepeatoperations1,2and3
Ifthereceiver’smemoryisfullitcannotbeenabledandthiswillbeindicatedbythe
buzzerB1soundingintermittently.
To cancel via radio a code through a transmitter already set in the memory:
1)PressP3forthreetimeswithin5s,thebuzzerB1willswitchonandsoundslowly.
2)Transmitthecodewhichistobecancelledwithin5s.Oncethechannelhasbeen
cancelledthebuzzerwillstopsounding.
Tocancelulteriorcodesrepeatpoints1and2.
Errors during the memorising
Ifthecodeisnotmemoriseditcouldbeduetothefollowingconditions:
-Thecodealreadyexistsinmemory
-Thememoryisfull(max.41codes).InthiscasetheBuzzerwillmake3bipeachtime
thepowerisswitchedonandduringthememorisation.
Antenna
Thecorrectinstallationandconnectionoftheantennaisfundamentalinorderto
obtainagoodrangefortheinstallation.
Connecta8.5cmpieceofwiretotheantennapoleconnectiononthedevice.
Asanalternative(andforbetterresults)useatunedantennaconnectedtothereceiver
viacoaxialcableRG58(impedance50Ω)withamaximumlengthof15metres
(mod.ANT868)
Technical specications
ReceiverRFsection
Receptionfrequency    868.3MHz
Intermediatefrequency   10.7MHz
Sensibility(nelytunedsignal)   1uV
Receivercodicationsection
Powersupply    230V

Operatingtemperaturerange   -20°–+60°C
Maximumpoweratthemotor
Voltage     230V
Power     350W
Maximumcommutablepoweratoutputashinglamp 230V 60W
Maximumcommutablepoweratoutputcourtesylamp 230V 300W
Maximumcommutablepowerat24V output 80mA
Maximumcommutablepower
atterminalboards22-23   35V,1A
Intheviewofaconstantdevelopmentoftheirproducts,themanufacturerreservestheright
forchangingtechnicaldataandfeatureswithoutpriornotice.

Description of the connections:
1 Inputgroundgeneralpowersupply
2 Inputgroundmotor
3 Inputgeneralpowersupply230V
phase
4 Inputgeneralpowersupply230V
neutral
5 Outputrelaycontactopening
6 Output230V
neutralbymeansoffuse(commommotor)
7 Outputrelaycontactclosing
8-9 OutputLP230V
60Wmax.forashinglamp
10-11 OutputLC230V
300Wmax.forcourtesylamp
12 Output24V
80mAforphotocells
13 Output24V
pushbuttonsandsafetycommon
14 Pushbuttonsandsafetycommon
15 Openingpush-button,normallyopenedordynamicpush-button(seedip-
  switchfunctions)
16 Closingpush-buttonnormallyopened
17 Stoppush-buttonnormallyopened
18 InputsafetydevicenormallyclosedFTC
19 Output12V


forOSE(max30mA)
20 InputsafetydeviceCSPresistive8,2Kohm
 (range6Kohm-10Kokm)
21 Pushbuttonsandsafetycommon
22-23 Normallyclosedcontactforsafetytest
24 Antennamass
25 Antennapole(wire8.5cm)

We also wish to remind you that if the N.C. (normally closed) contacts are not
used they should be jumpered:
- If FTC input is not used, 18-22 and 23-21 contacts must be jumpered
- If CSP input is not used 20-21 must be jumpered, set J1 as n.c. and memorise
the buffer barrier as described at page 1
- If TB input is not used 17-21 must be jumpered
The earth wire must be longer of the other wires because it must be the last to
break off if the cable clamps slacking.
Remember that there are specic standards that must be complied with both
as regards the safety of the electrical systems and as regards the remote control
of tubular motors for roller blind.

TELECO AUTOMATION TVPRP868A01 Specifications

General

Brand	TELECO AUTOMATION
Model	TVPRP868A01
Category	Remote Control
Language	English