ll-eleflex
MARINE
640 North Lewis Road
Limerick, PA 19468 USA
61 0-495-701 1
www.teleflexmari ne. com
sH 521015215
BACK TOUilT RACK.
HELT
TNSTRUGTIONS
Copyright
I 998,
Teleflex lncorporated
(USA)
ALLER:
THESE
INSTRUCTIONS
COltlTAlN
IilPORTANT SAFETY lt{FORtATIOl{ AND ilUST
BE
FORWARDED TO
These
instrudions
describe
how to
install helm
assemblies
for
'THE
BACK
MOUNT
RACK' steering
system.
Additionalcomponents
required to complete
the
system
are:
.
SC 134u, Cable
(for
single cable
system)
.
SC 135n< Cable
(for
dual cable
system)
.
SB 39526
Bezel
Kit
(Required
to
mount helm
to
dash)
.
Steering
Wheel
(max.
dia.
16
in.- see
Telefl€x
Catalog)
.
Engine Connection
Kit
(see
Teleflex
catalog)
Optional
components
are:
.
SB
2744810 degree
Mounting Kit
.
SB 27449
20
degree
Mounting Kit
.
SA39531
Torque Brake
NOTE: HELMS AND CABLE
ASSEMBLIES ARE
SUPPLIED LUBRICATED READY FOR INSTALL-
ATION,
DO NOT ADD ANY LUBRICANT
TO EITHER
ASSEMBLY.
USE OF OTHER LUBRICANTS
CAN
CAUSE DAIVIAGE TO THE
STEERING
CABLE,
RESULTING
IN THE CABLE SEIZING
OR PRE-
MATURE
WEAR. KEEP THE
CABLE AND DRIVE
ASSEMBLY
CLEAN DURING
INSTALTATION.
DIRT
WILL
DAMAGE
THE SYSTEM AND
CAUSE
PREMATURE
WEAR
,,r'r};
20
STEIiII{G ITIEEL
IINIIUT
fOUttlTlXG PL TE ILLOWS 20" FROI IIORIZO]|TTL
tt{ EtTHEn DtRlcTtox
FIGURE 1
IIISIDE FACE
OF GUIIIIEL
7"*
9'/zi'->1
I
|
''/:
cEilTqtxE_gE
rtE.ruc'-__
The Helm Assembly
can be
mounted for
either
port
or
starboard
cable
entry. Steering cables,
where
possible,
should
be routed
to the starboard side of the
boat
to
balance
engine torque.
PREPARATIO]I
FOR I]ISTALLATIO]I
Stsp+-
@
Helm
Assemtily on
the dashboard.
CAUTTON:
E/VSURE THAT
THE
CLEARANCES
SHOWN
ON FIGURES 1 AND
2 ARE MAINTAINED.
ENSURE
THAT THE STEERING
WHEEL DOES NOT
INTERFERE
WITH
OTHER
DASHBOARD
EQUIPMENT
SUCH AS ENGINE COA'IROLS
AND'NSTR
UMENTS.
Step 2. Locate template
in
position
selected. NOTE:
TEMPTATE FOR 20 DEGREE
MOUNT DIFFERS
FROM
TEMPTATE
FOR 90
AND
10 DEGREE
MOUNTS.
ENSURE
THAT
THE
CORRECT
ONE
IS
USED. Drill
one
hole 2
/t"
dlameter
and 3 holes 5/16"
diameter.
WARI{ING
EEFORE STARTIITIG
INSTATLATION
READ
THESE IIiISTRUCTIONS
AND ENGII{E
TAIGRS INSTRUCTIOI{S THOROUGHLY. FAILURE
TO FOLLOW E]THER OF
THESE INSTRUCTIOIIIS
OR
INCORRECT
ASSEilBLY CAt{ RESULT
IN LOSS OF CONTROL AND
CAUSE
PROPERTY
DATAGE OR II{JURY,
DO iIOT
SUBSTITUTE
PARTS FROT
OTHER ITAIIUFACTURERS,
THEY
MAY CAUSE
A SAFETY HAZARD FOR WHICH TELEFLEX
IilC.,
USA
CAI{}IOT ACCEPT RESPONSIBILITY.
TO AVOID
EXCESSIVE STEERING LOADS, AI{D TO GET THE BEST
STEERITIG
PERFORTAI{CE,
THE
OUTBOARD TIOTOR OR
OUTDRIVE
TRIT TABS AND TILT POS]TIO]{ ]TIUST 8E ADJUSTED
AS INSTRUCTED
IN THE TIOTOR MANUFACTURERS
OPERATION
MANUAL. FAILURE
TO DO
SO
CAI{ EFFECT THE
PERFORTANCE
DO NOT ATTACH ANY ELECTRICAL
GROUiID WIRES TO THE
HELM. THIS WOULD RESULT IltI AliI ELECTROLYTIC
REACTION
TO THE
STEERING CABLE
THAT MAY
RESULT IN
CABLE
FAILURE OR GREATLY
REDUCED
SERVICE LIFE.
WARNING
i'UST
NOT BE DISASSETBLED FOR
. FAILURE TO
RE.ASSETIBLE CORRECTL
Y LEAD TO
TOTAL FAILURE
OF
THE
COULD
RESULT IN PERSONAL INJURY
7/98 Rev. 1
Page 1
of4
ts-sH5210/15
To Next Page
Need help?
General