Teshow TS81B - User Manual

Digital PID Controller
TS80B-E1
Carefully read all the instructions in this manual. Please place
this manual in a convenient location for easy reference.
WARNING
CAUTION
(4) Control output [OUT]:
M:Relay contact V: Voltage pulse
8: Current(DC4 ~ 20 mA) 5: DC0-5VDC
6: DC0-10VDC T: Trigger (for triac driving)
(5) Remark:
N: No
(6) Alarm 1[AL1 for high alarm] See"5.5 "
N: No alarm
A: Deviation high alarm H: Process high alarm
(7) Alarm 2[AL2 for low alarm] See"5.5 "
N: No alarm
B: Deviation low alarm J: Process low alarm
(8) Power
A: 220VAC B 85-265VAC D 24VDC E 24VAC
Initial Setting
Initial Setting
!
TS80B-E1
INSTRUCTION MANUAL
1
An external protection device must be installed if failure of this
instrument could result in damage to the instrument, equipment
or injury to personnel .
All wiring must be completed before power in turned on to prevent
electric shock, fire or damage to instrument and equipment .
This instrument must be used in accordance with the
specifications to prevent fire or damage to instrument and
equipment.
This instrument is not intended for use in locations subject to
flammable or explosive gases.
Do not touch high-voltage connections such as power supply
terminals , etc. to avoid electric shock.
This instrument is protected from electric shock by reinforced
insulation. Provide reinforced insulation between the wire for
the input signal and the wires for instrument power supply, source
of power and loads.
This instrument is design for installation in an enclosed
instrumentation panel. All high-voltage connections such as
power supply terminals must be enclosed in the instrumentati on
panel to avoid electric shock by operating personnel.
All precautions described in this manual should be taken to avoid
damage to the instrument or equipment.
All wiring must be in accordance with local codes and regulations.
Always observe precautions described in this manual.
Otherwise serious injury or accident may result.
Do not allow metal fragments or lead wire scraps to fall inside this
instrument. This may cause electric shock, fire or malfunction.
Firmly tighten each terminal screw at the specified torque.
Otherwise electric shock or fire may result.
Do not place any obstacle around this instrument in order
not to impede radiation of heat. And do not close ventilation holes.
Do not connect wires to unused terminals.
Before cleaning the instrument, always turn off the power supply.
Remove stains from this instrument using a soft, dry cloth. Do not
use a volatile solvent such as thinner in order to avoid deformation
or discoloration.
Do not rub nor strike the display unit of this instrument with a hard
object.
-
1. PRODUCT CHECK
-
(1) Control action
F: PID reverse action with autotuning
(1)
(2)
(3) (4) (5) (6)(7) (8)
(2) Input type,(3) Range code: See"8.INPUT RANGE TABLE"
Check MODEL and CODE
is very important when ordering.
2.1 Mounting Cautions
2. MOUNTING
(1) Use this Instrument within the following ambient
temperature and ambient humidity.
Allowable ambient temperature: 0 to 50
Allowable ambient humidity: 45 to 85% RH
(2) Avoid the following when selecting the mounting location.
Rapid changes in ambient temperature which may cause condensation.
Corrosive or inflammable gases.
Direct vibration or shock to the mainframe.
Water,oil,chemicals,vapor or steam splashes.
Excessive induction noise, static electricity, magnetic fields or noise.
Direct air flow from an air conditioner.
Exposure to direct sunlight.
Excessive heat accumulation.
C
TS81B/TS84B/TS85B/TS87B/TS89B
TS85B
TS84B
TS89B
TS87B
TS81B
Example
Model: TS89B
Specification:
Model of the controller:TS89B
Size: 96mm x 96mm
Control action: PID reverse action
Input: K type thermocouple
Out put: Relay output
Alarm: 1 deviation high alarm (AL1)
Power: AC220V
Code: FKA4-MN*AN-A
2.2 Dimensions
TS81B
50
14.6
50
44.0
44.0
58.0
80
13.6
1
1
TS84B
TS85B
50
14.6
96
44.0
90.0
104.0
80
13.6
1
1
74
14.6
74
67.5
67.5
80.0
80
13.6
1
1
UP
TS87B
TS89B
90
96
14.6
96
90.0
104.0
80
13.6
1
1
UP
Unit:mm
Unit:mm
Unit:mm
Unit:mm

Summary

Product Check

Mounting

Mounting Cautions

Guidelines for safe and optimal installation within specific environmental conditions.

Dimensions

Physical dimensions and cutout sizes for various controller models.

Mounting Procedures

Step-by-step guide for securely installing the instrument into a panel.

Wiring

Wiring Cautions

Important safety and performance guidelines for electrical connections.

Terminal Configuration

Diagrams showing terminal assignments for different controller models.

Parts Description

Component Overview

Description of the controller's display, buttons, and indicator lamps.

Setting

Setting Procedures

Steps for navigating modes, setting SV, and changing parameters.

PID Level Parameter List

List of PID parameters with their setting ranges and descriptions.

Initial Setting Parameters

Detailed guide for initial configuration and parameter adjustments.

PID Autotuning (AT) Function

Autotuning (AT) start

Instructions on how to initiate the automatic PID tuning process.

Requirements for AT start

Conditions necessary before starting the autotuning function.

Requirements for AT cancellation

Scenarios that will cause the autotuning process to be terminated.

Error Displays

Error display

Explains RAM failure errors and troubleshooting steps.

Overscale and Underscale

Describes PV display errors when values are out of the input range.

Input Range Table

Teshow TS81B Specifications

General

Model	TS81B
Category	Controller
Standby Time	30 days
Platform	Android, iOS
Compatibility	Android, iOS, HarmonyOS, Switch
Battery	Built-in rechargeable battery
Charging Port	USB Type-C