What to do if I have a ground fault with my Tesla Battery Charger?
To resolve a ground fault with your Tesla Battery Charger, disconnect the handle from the car, then reconnect and try again. If the issue continues, turn OFF the circuit breaker servicing the Wall Connector for 10 seconds, then turn it ON again and retry. If the problem still persists, contact Tesla.
What to do if my Tesla 1069742-00-A Battery Charger has over temperature protection?
To address over temperature protection on your Tesla Battery Charger, ensure the Wall Connector, vehicle connectors, and wall plug (if used) are not covered and have no nearby heat source. If the issue continues at normal ambient temperatures (under 100°F or 38°C), contact Tesla.
How to fix Pilot fault on Tesla 1069742-00-A?
To fix the 'Pilot fault' on your Tesla Battery Charger, try plugging your vehicle into another Wall Connector or the Mobile Connector that came with your vehicle. If the problem persists, contact Tesla.
What to do for over current protection on Tesla 1069742-00-A Battery Charger?
To resolve over current protection on your Tesla Battery Charger, reduce the charge current setting in your vehicle. If the problem continues and your vehicle is a Tesla, contact Tesla. If it's a non-Tesla vehicle, contact its manufacturer.
What to do if no ground connection detected in Tesla Wall Connector?
If your Tesla Wall Connector has no ground connection, ensure it is properly grounded. If you're uncertain, consult your electrician for correct grounding at your circuit breaker or power distribution box and for proper connection to the Wall Connector.
What to do if Tesla Wall Connector input miswired?
If your Tesla Wall Connector input is miswired (possibly Line and Neutral are swapped), the input wiring between the wall power and the Wall Connector has been improperly installed. Consult your electrician.
What to do for over or under voltage protection on Tesla 1069742-00-A Battery Charger?
For over or under voltage protection issues with your Tesla Battery Charger, consult your electrician for proper voltage on the circuit breaker servicing the Wall Connector.
What to do if Tesla 1069742-00-A Battery Charger has more than one Wall Connector set to Master?
If your Tesla Battery Charger's Circuit Breaker Sharing Network has more than one Wall Connector set to Master, set one of the Wall Connectors to Slave.
What to do if Tesla 1069742-00-A Battery Charger has more than three Wall Connectors set to Slave?
If your Tesla Battery Charger's Circuit Breaker Sharing Network has more than three Wall Connectors set to Slave, move one or more Wall Connectors to a different circuit and disconnect it from this Circuit Breaker Sharing Network.
Details FCC and Industry Canada compliance for the device, including interference conditions.
Instructions for reporting any inaccuracies or omissions in the manual to Tesla.
Information on Tesla's intellectual property rights and registered trademarks.
Crucial instructions and warnings to be followed during installation and maintenance of the Wall Connector.
Critical safety precautions and potential hazards associated with using the Wall Connector.
Important considerations and potential risks when operating or installing the Wall Connector.
Additional guidance and important reminders regarding installation and handling of the Wall Connector.
Explanation of how to adjust circuit breaker ratings for optimal charging speed.
Description of the Wall Connector's automatic fault detection and recovery capabilities.
How the Wall Connector automatically resumes charging after a power interruption.
Information on connecting multiple Wall Connectors to a single circuit for shared load capacity.
Essential prerequisites and steps before installing the Wall Connector.
Guidelines and warnings for connecting the Wall Connector to the electrical service.
Diagram and explanation for single-phase 240V installation wiring.
Wiring diagram and safety notes for 208V 3-phase Wye-connected installations.
Wiring diagram and safety notes for 240V 3-phase Delta-connected installations.
Wiring diagram and safety notes for 277V 3-phase Wye-connected installations.
Guidance on selecting the correct circuit breaker based on site availability.
Factors to consider when selecting the optimal mounting location for the Wall Connector.
General guidelines and factors to consider during the installation process.
Instructions and diagrams specific to the top entry wiring method for installation.
List of tools and materials needed to perform the Wall Connector installation.
A high-level summary of the sequential steps involved in installing the Wall Connector.
Detailed instructions for mounting the low profile bracket for rear or bottom conduit entry.
Detailed instructions for mounting the top entry bracket for top conduit entry.
Steps to prepare the Wall Connector housing and route wiring before final mounting.
Instructions for connecting the service wiring to the Wall Connector's terminal block.
Guide to configuring the Wall Connector's operating current using DIP and rotary switches.
Final steps to reassemble the Wall Connector and safely apply power.
Procedures for resetting the Wall Connector to resolve faults or reboot the device.
Contact information for support and further assistance from Tesla.
Instructions for connecting multiple Wall Connectors in a daisy-chain configuration.
Diagram illustrating the communication wiring setup for a daisy-chained network.
Overview of the warranty coverage, exclusions, and limitations for Tesla charging equipment.
Details on the extent of Tesla's liability and disclaimers for warranty claims.
Procedures for enforcing warranty terms and resolving disputes with Tesla.
General| Brand | Tesla |
|---|---|
| Model | 1069742-00-A |
| Category | Battery Charger |
| Language | English |
To Next Page
