[Important Notice for Users of this Product in Japan]
This development kit is NOT certified as Confirming to Technical Regulations of Radio Law of Japan
If you use this product in Japan, you are required by Radio Law of Japan to follow the instructions below with respect to this product:
1. Use this product in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal Affairs and Communica-
tions on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for Enforcement of Radio Law of Japan,
2. Use this product only after you obtained the license of Test Radio Station as provided in Radio Law of Japan with respect to this product, or
3. Use of this product only after you obtained the Technical Regulations Conformity Certication as provided in Radio Law of Japan with respect to this
product. Also, please do not transfer this product, unless you give the same notice above to the transferee. Please note that if you could not follow the
instructions above, you will be subject to penalties of Radio Law of Japan.
Texas Instruments Japan Limited
(address) 24-1, Nishi-Shinjuku 6 chome, Shinjuku-ku, Tokyo, Japan
http://www.tij.co.jp
【ご使用にあたっての注意】
本開発キットは技術基準適合証明を受けておりません。
本製品のご使用に際しては、電波法遵守のため、以下のいずれかの措置を取っていただく必要がありますのでご注意くださ
い。
（１）電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波
暗室等の試験設備でご使用いただく。
（２）実験局の免許を取得後ご使用いただく。
（３）技術基準適合証明を取得後ご使用いただく。
なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。
上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。
日本テキサス・インスツルメンツ株式会社
東京都新宿区西新宿６丁目２４番１号
西新宿三井ビル
http://www.tij.co.jp
EVALUATION BOARD/KIT/MODULE (EVM)WARNINGS, RESTRICTIONS AND DISCLAIMERS
For Feasibility Evaluation Only, in Laboratory/Development Environments. Unless otherwise indicated, this EVM is not a finished electrical
equipment and not intended for consumer use. It is intended solely for use for preliminary feasibility evaluation in laboratory/development environments
by technically qualified electronics experts who are familiar with the dangers and application risks associated with handling electrical mechanical com-
ponents, systems and subsystems. It should not be used as all or part of a finished end product.
Your Sole Responsibility and Risk. You acknowledge, represent and agree that:
1 You have unique knowledge concerning Federal, State and local regulatory requirements (including but not limited to Food and Drug Administra-
tion regulations, if applicable) which relate to your products and which relate to your use (and/or that of your employees, affiliates, contractors or
designees) of the EVM for evaluation, testing and other purposes.
2 You have full and exclusive responsibility to assure the safety and compliance of your products with all such laws and other applicable regulatory
requirements, and also to assure the safety of any activities to be conducted by you and/or your employees, affiliates, contractors or designees,
using the EVM. Further, you are responsible to assure that any interfaces (electronic and/or mechanical) between the EVM and any human body are
designed with suitable isolation and means to safely limit accessible leakage currents to minimize the risk of electrical shock hazard.
3 You will employ reasonable safeguards to ensure that your use of the EVM will not result in any property damage, injury or death, even if the EVM
should fail to perform as described or expected.
4 You will take care of proper disposal and recycling of the EVM’s electronic components and packing materials.
Certain Instructions. It is important to operate this EVM within TI’s recommended specifications and environmental considerations per the user guide-
lines. Exceeding the specified EVM ratings (including but not limited to input and output voltage, current, power, and environmental ranges) may cause
property damage, personal injury or death. If there are questions concerning these ratings please contact a TI field representative prior to connecting
interface electronics including input power and intended loads. Any loads applied outside of the specified output range may result in unintended and/
or inaccurate operation and/or possible permanent damage to the EVM and/or interface electronics. Please consult the EVM User's Guide prior to con-
necting any load to the EVM output. If there is uncertainty as to the load specification, please contact a TI field representative. During normal operation,
some circuit components may have case temperatures greater than 60°C as long as the input and output are maintained at a normal ambient operating
temperature. These components include but are not limited to linear regulators, switching transistors, pass transistors, and current sense resistors which
can be identified using the EVM schematic located in the EVM User's Guide. When placing measurement probes near these devices during normal opera-
tion, please be aware that these devices may be very warm to the touch. As with all electronic evaluation tools, only qualified personnel knowledgeable
in electronic measurement and diagnostics normally found in development environments should use these EVMs.
Agreement to Defend, Indemnify and Hold Harmless. You agree to defend, indemnify and hold TI, its licensors and their representatives harmless
from and against any and all claims, damages, losses, expenses, costs and liabilities (collectively, "Claims") arising out of or in connection with any use
of the EVM that is not in accordance with the terms of the agreement. This obligation shall apply whether Claims arise under law of tort or contract or
any other legal theory, and even if the EVM fails to perform as described or expected.
Safety-Critical or Life-Critical Applications. If you intend to evaluate the components for possible use in safety critical applications (such as life
support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, such as devices which are classified
as FDA Class III or similar classification, then you must specifically notify TI of such intent and enter into a separate Assurance and Indemnity Agreement.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2012, Texas Instruments Incorporated
To Previous Page
Loading...
Need help?
General
