SERVICE KIT
SK 208-179B
• The windshield w as her tube at the positions that follow: Leav e the mounts attached and
do not cut the tubing at this t im e.
• At FS 166.148 attach the prop tube
• At FS 176.19 attach the prop tube
• At FS 179.346 attach the right wing tube
• At FS 184.43 do not att ac h a ny thing at this mount.
• At F S 18 6.17 attach the left wing tee to the prop tee tube
• At F S 188.98 atta ch the left wing tee to the prop tee tube.
C. (Refer to Figure 3.) Install S 2034-1 Mounts at t he positions that follow to at ta ch the windshield tube:
• (Refer to Figure 3, View D-D.) one at RBL 8. 00 (approx im ate ly FS 160.528)
• Refer to Figure 3, View C-C.) one at FS 158.032 for th e n ew belly tube and the new windshield
tubing installa tio n. The belly tube and the w indshield tubing will bo th us e this mount.
(1) Drill two Number 30 (0.128-inc h diameter) holes at th e positions shown.
(2) Apply Alodine to bare m etal.
(3) With the two MS20470A4-6N Riv ets, attach the two S 2034-1 Mo unt s t o the structure.
D. Inst all S 2034-1 Mounts at the positions that follow t o attach the new tee to belly tube:
• (Refer to Figure 3, View J-J.) at LBL 23.43 (at approxim ately FS 207. 192)
• (Refer to Figure 3, View H -H. ) at FS 20 1.74 (the left wing tube and the belly to te e tube both
use this m ount )
• (Refer to Figure 3, View G-G.) at FS 176. 99
• (Refer to Figure 3, View F-F. ) at B L0. 00 (at approximately FS 170.48)
• (Refer to Fi gure 3, View E-E.) at FS 166. 45
• (Refer to Figure 3, View C-C.) at FS 158.032 (this one is inst all ed abov e and s hares with
the win ds hield tube).
• Keep the ex isting m ounts at the positions that follow (Th e left wing tee to prop tee and the bell y
to t ee tub e both us e these mounts)
1. at FS 188 .78
2. at FS 186 .17
(1) Drill s ix Nu mber 30 (0.128-inch diameter) holes at t he pos it ions sh own for the mounts that
you will install.
(2) Apply Alodine to bare m etal.
(3) With the six MS20470A4-6N Rivets, attach the six S2034-1 M ounts to the s t ruc ture.
E. Use S 2209-2 Ties to attach the t ubing to the struct ure at t he S203 4-1 Mounts and to other attach
points as neces s ary to make sure that there wi ll be n o chafing and that there will be sufficient
clearance for the tubing.
F. (Refer to Figure 4, View A-A.) With th e k ept attachment hardware, install the kept H610024
windshield tube and the new H610026 tee-to-be lly t ube with n ew sealing rings.
(1) Install the aft end of t he tee to belly t ube at the kept MN6210 Equal Tee, Bulkhead with the
three new 100-013-8810 Seali ng Rings. Correctly tighten the tee nuts at this tim e (make sure
that the tee inlet po ints outboard).
(2) Do the routing of the kept windshield tube.
(3) (Refer to Figure 4, View C-C) At tach the kept win ds hield tube (cut to length) and the new tee to
belly tube at the ne w tank pos ition (FS 153.711).
G. (Refer to Figure 17, View B-B.) A ttach the H610024 Nylon Tubing to the M N6235 Short Bulkhead
Connector at t he 2613495 TKS Connectors Doubler with the kept hardware and a new S2800-943
Sealing Ring.
H. Atta ch the H610026 Nylon Tubing t o t he MN6216 Bulkhe ad Unequal Tee at the 2613495 TKS
Connectors Doubler with the kept attachment hardware a nd a new 100-013-8810 Seal.
SK208-179B
February 7, 2013 Page 27
To Next Page
Loading...
