The Bear Chair BC201 User Manual

# Description Qty/Qte
1. Legs/Pieds 2
2. Seat Slats/Lames de siège 6
3. Arm Support/Soutiens des Bras 2
4. Triangles/Triangles 2
5. Arms/Bras 2
6. Additional Arm Support/
Soutien de bras additionnel 1
7. Struts/Supports 2
8. Sides/Côtés 2
9. Bottom Back Support/
Support intérieur du dossier 1
10. Back Slats/Lames du dossier 7
11. Top Back Support/
Support supérieur du dossier 1
12. Front Slat/Lame du devant 1
13. Comfort Slat/Lame de confort 1
14. Plated Screws/Vis 68
15. Brass Plaque/Plaque en laiton 1
Set the bottom back support (#9) and
top back support (#11) on a at surface
with the curved sides and countersunk
holes facing up. Arrange the seven back
slats (#10) with the longest in the centre,
on the supports.
Déposer les deux soutiens arrières du dossier, soit
les soutiens supérieur (#9) et inférieur (#11), sur
une surface droite avec les côtés courbés et les
trous fraisés vers le haut. Disposer les sept lames
du dossier (#10) sur les soutiens en mettant la plus
longue au centre.
KIT CHAIR BC201

 Phone: (705)386-0757
 Fax: (705)386-0915
 TollFree: 1-800-421-1406
Box509,SouthRiver,OntarioP0A1X0
PARTS LIST
Attach the back of the arm (#5) to the
strut with one screw through the pre-
drilled hole on the strut. Attach the
front of the arm to the arm support (#3)
with two screws from the under side.
Visser l’arrière des bras (#5) aux supports (#7)
avec une vis dans le trou pré-percé dans chacun
des supports. Visser le devant de chacun des bras
(#3) avec deux vis dans les trous pré-percés à son
soutien de bras.
Place the chair on a at surface and
make sure it is sitting solid on both legs
and both sides. If it is not sitting at,
remove the single screw holding the
bottom of the strut down and move the
strut up or down to compensate. When
the adjustments are done, attach the
struts with two screws each (and glue).
Placer la chaise sur une surface plane et faire
certain qu’elle est solide sur ses deux pattes et sur
les deux côtés. Si ce n’est pas le cas, dévisser une
des vis du bas du support et déplacer le support
vers le haut ou le bas pour faire l’ajustement. Une
fois la chaise ajustée, visser avec deux vis chacun
des deux supports (et de la colle).
Attach the additional arm support (#6)
to the inside of the struts, underneath
the back of the arms through the pre-
drilled holes with four screws.
Congratulations – try it out!
Visser le soutien de bras additionnel (#6) à
l’intérieur des supports et en-dessous des bras
avec quatre vis dans les trous pré-percés.
Felicitations – essayer la!
10)
11)
12)
1)
1514



The Bear Chair BC201 Specifications

General

Brand	The Bear Chair
Model	BC201
Category	Indoor Furnishing
Language	English

Summary

Assembly Instructions

Step 1: Back Assembly Construction

Assemble the back supports and slats, securing the center slat first, then spacing and attaching the remaining slats.

Step 2: Attach Legs to Sides

Connect the legs to the sides using pre-drilled holes and screws, ensuring correct left/right matching.

Step 3: Attach Front Slat to Sides

Join the front slat to the two sides, aligning them with the legs and using four screws.

Step 4: Attach Back Assembly to Sides

Position the assembled back onto the sides and secure it with two screws through pre-drilled holes.

Step 5: Install Seat and Comfort Slats

Place the comfort slat and six seat slats evenly on the sides, leaving a small gap from the back assembly.

Step 6: Attach Arm Supports and Triangles

Secure arm supports to legs with screws, then attach triangles to the corner using three screws each.

Step 7: Attach Struts to Back Support

Connect the top of the struts to the underside of the top back support with screws. Adjust for alignment.

Step 8: Attach Struts to Sides

Attach the bottom of the struts to the sides with one screw each, avoiding glue for now.

Step 9: Attach Additional Arm Support

Attach the additional arm support to the inside of the struts, underneath the back of the arms using four screws.

Step 10: Attach Arm to Strut and Front

Connect the rear of the arm to the strut with one screw, and the front of the arm to the arm support with two screws.

Step 11: Level Chair and Secure Struts

Ensure the chair sits flat, adjust strut position if needed, and secure struts with two screws each and glue.