Therma-Tru Double-door

To Next Page

SPEC

Door System

Specifications

DOOR PANELS

OPTIONAL

FACTORY-GLAZED

GLASS OR GLASS

INSERTS

GASKETING,

WEATHERSTRIPPING

HINGES, STRIKES

FRAMES

SILL, SWING-IN, SWING

OUT, SIDELITE OPTIONS

TRANSOM OPTIONS

⎠

Classic-Craft Door System Specifications

OPTIONAL

DECORATIVE PANELS

Faces: 3/32-inch minimum thickness, molded from proprietary thermoset composite,

wood-grained to duplicate hand-crafted red oak master, stainable and paintable. Door

edges: machinable kiln-dried clear northern red oak, flush and square with door faces,

lock edge reinforced with full-length 3-1/2-inch wide engineered lumber core. Door

bottom edge: moisture-proof and decay-proof composite. Core: foamed-in-place

polyurethane, CFC-free, density 2.0 pcf minimum, K-factor of 0.15 for minimum

thermal transmittance. Standard factory sizes may be edge trimmed or end trimmed in

shop or field to suit replacement door size requirements.

Factory-glazed (available in sidelites):

Inserts (lites):

perimeter moldings flush with skin and made as

integral part of skin, molding details match door panel moldings. Glass: minimum 1/8-

inch tempered, two thicknesses with sealed airspace between, air-space typically 1/2-

inch. Options for leaded decorative glass triple-glazed in airspace between tempered

glass faces with solid brass or zinc caming. Etched glass options. Optional removable

red oak wood grilles.

perimeter frames in raised-molding patterns, composite frame moldings

wood grained to match door faces, with molding patterns complementing raised panel

moldings, stainable or paintable, screw-fastened to doors, screw holes concealed with

grain-matched plugs in matching material and finish. Glass: minimum 1/8-inch

tempered, two thicknesses with sealed airspace between, airspace typically 1/2-inch.

Options for leaded decorative glass triple-glazed in air space between tempered glass

faces with solid brass caming. Options for etched glass. Optional removable red oak

wood grilles.

Molded from fiberglass-reinforced thermoset composite, wood grained to match door

faces, stainable or paintable, fastened with very high bond tape.

Swing-in models: , press-fit in kerfs at jamb stops in

frames. Extruded thermoplastic elastomer, finned and chambered design, press-fit into

bottom edge of doors. Corner pads at bottom margin corners from jacketed thermoset

closed-cell foam.

jacketed thermoset closed-cell foam

Steel, zinc-plated, brass finish. Optional solid brass hinges. Screws plated and finished

to match hardware. Minimum hinge size 4x4x.098 inches. Strikes are proprietary

adjustable type, permitting in-out adjustment of door in frame, up to 3/16 inch.

Milled from 5/4 kiln-dried pine, profiled with 1/2-inch stop, minimum depth 4-9/16

inches. Other frame depths available to match wall constructions. Exterior casing

brickmould in WM180 pattern available. Optional frames in clear northern red oak or

exterior grade red oak wrap over pine with matching brickmould. Optional maintenance-

free clad frames and brickmoulds in prefinished white color.

Wide range of sill options:

Double-door models:

Sidelite options:

thermally-broken fixed, adjustable with oak threshold, in

“monumental” grade with decay proof composite substrate, available bronze and brass

finishes, other sills available in swing-in, swing-out, aluminum, brass or bronze anodized

finish.

double door in 6/8 height available with both leaves active and

locking astragal available, astragal faces in clear northern red oak to match door.

flush-glazed lite models, raised molding models and raised panel

models with glass moldings to match door panel moldings, in 12-inch and 14-inch

widths. Sidelite systems available with mullions separating doors from sidelites, and

continuous sills and frame head, or as separately framed and cased units joined together.

Transom frames, either rectangular or elliptical, match door frames and have matching

exterior brickmould. Transom frames in primed pine or clear northern red oak to match

door frame option. Clear insulated glass, etched glass or with decorative leaded glass,

detailed with solid brass or zinc caming.

Issued: Oct 2008

Need help?

Do you have a question about the Therma-Tru Double-door and is the answer not in the manual?

Summary

Classic-Craft Door System Specifications

Door Panels

Faces: 3/32-inch minimum thickness, molded thermoset composite, wood-grained for stainability.

Optional Factory-Glazed Glass or Glass Inserts

Factory-glazed sidelites with flush moldings. Glass options include tempered, triple-glazed decorative.

Optional Decorative Panels

Molded fiberglass-reinforced composite panels, wood-grained, stainable or paintable.

Gasketing and Weatherstripping

Jacketed thermoset closed-cell foam and extruded thermoplastic elastomer for sealing.

Hinges and Strikes

Steel, zinc-plated or brass finish hinges. Proprietary adjustable strike plates.

Frames

Milled from 5/4 kiln-dried pine, with various depth options and brickmould casing.

Sill, Swing-in, Swing Out, Sidelite Options

Range of sill options including thermally-broken fixed and adjustable, various finishes.

Transom Options

Rectangular or elliptical transom frames matching door, with glass or decorative options.

Fiber-Classic Door System Specifications

Door Panels

Faces: 1/16-inch fiberglass-reinforced composite, wood-grained, stainable/paintable.

Optional Factory-Glazed Glass or Glass Inserts

Factory-glazed sidelites with flush moldings. Glass options: tempered, Low-E, grille between glass.

Optional Decorative Panels

Molded composite panels, wood-grained, stainable or paintable, secured with high bond tape.

Gasketing and Weatherstripping

Jacketed thermoset foam for swing-in, extruded elastomer for bottom edge, integral gaskets for swing-out.

Hinges and Strikes

Steel, zinc-plated, brass or chrome finish hinges. Adjustable strike plates for frame fit.

Frames

Milled from 5/4 kiln-dried pine, profiled for stop, with optional maintenance-free clad frames.

Sills, Swing-in, Swing-out, Patio Door, Sidelite Options

Sill options include thermally-broken, adjustable oak, aluminum, brass, bronze finishes.

Transom Options

Rectangular or elliptical transoms matching door frames, with clear or decorative glass.

Steel Door System Specifications

Door Panels

Faces: .021-inch (24 gauge) steel, zinc-coated, conversion-coated for paint bond.

Optional Glass Insert Lites

Inserts: frames with raised moldings. Glass: tempered, dual-pane, optional decorative glass.

Gasketing, Weatherstripping

Magnetic or jacketed foam for swing-in, extruded elastomer for bottom edge.

Hinges, Strikes

Steel, zinc-plated, brass or chrome finish hinges. Adjustable strike plates.

Frames

Milled from 5/4 kiln-dried pine, profiled with 1/2-inch stop, optional clad frames.

Sill, Swing-in, Swing Out, Sidelite Options

Sill options: thermally-broken, adjustable oak, aluminum, brass, bronze anodized finishes.

Transom Options

Transom frames matching door, with clear insulated or decorative leaded glass.