Why is there white powder from my Thermablaster WDFT250-VF-IR?
If you notice white powder residue forming within the burner box or on adjacent walls or furniture when using your Thermablaster Heater, it's likely because: * When heated, the vapors from furniture polish, wax, carpet cleaners, etc., turn into white powder residue. Solution: Turn the heater off when using furniture polish, wax, carpet cleaner, or similar products.
Why is there a gas odor during combustion in my Thermablaster WDFT250-VF-IR Heater?
If you notice a gas odor during combustion in your Thermablaster Heater, disassemble the gas tubing and remove any foreign matter. Also, locate and correct all leaks.
How to get rid of unwanted odors from Thermablaster WDFT250-VF-IR?
If the Thermablaster Heater produces unwanted odors, ventilate the room and stop using any odor-causing products while the heater is running. You may also need to locate and correct any gas leaks or refill the supply tank if you have a propane/LP model.
What to do if there is a spark but no ignition on my Thermablaster WDFT250-VF-IR?
If, when you press the igniter button on your Thermablaster Heater, there is a spark at the ODS/pilot but no ignition, first ensure the gas supply is turned on or the equipment shutoff valve is open. Fully press in the control knob while pressing the igniter button, and continue holding it down, repeating the igniting operation until air is removed. Also, ensure the control knob is in the PILOT position. You might also need to clean or replace the ODS/pilot assembly or replace the gas regulator. If problems persist, contact your local propane/LP gas company.
Why does my new Thermablaster WDFT250-VF-IR Heater smoke?
If you notice slight smoke or odor during the initial operation of your Thermablaster Heater, it is likely due to: * Residues from manufacturing processes. The problem will stop after a few hours of operation.
What to do if Thermablaster Heater burner won't light?
If the burner(s) on your Thermablaster Heater do not light after the ODS/pilot is stably lit, it could be due to: * A clogged burner orifice. Solution: Clean or replace the burner orifice. * Burner orifice diameter is too small. Suggested solution: Contact customer service. * Inlet gas pressure is too low. Suggested solution: Contact your local gas supplier.
Why is my Thermablaster WDFT250-VF-IR whistling?
If your Thermablaster Heater makes a whistling noise when the burner is lit, the cause might be: * Turning the control knob to the Hi position when the burner is cold. Solution: Turn the control knob to the LO position and let it warm up for a minute. * Air in the gas line. Solution: Operate the burner until the air is removed from the line. Have the gas line checked by your local gas supplier. * Air passageways on the heater are blocked. Solution: Observe minimum installation clearances. * Dirty or partially clogged burner orifice. Solution: Clean or replace the burner.
How to fix Thermablaster Heater when there is no spark?
If there is no spark at the ODS/pilot when the igniter knob is pressed on your Thermablaster Heater, the following could be the reasons: * The igniter electrode is positioned wrongly. Solution: Reposition the igniter electrode. * Cables between the switch, battery pack, igniter, and igniter electrode may be loose, pinched, wet, or broken. Solution: Secure or replace the cables. * The igniter is bad. Solution: Replace the igniter. * There is no battery or the battery is used up. Solution: Install or replace the battery.
Why does my Thermablaster Heater click or tick after being lit or shut off?
This clicking/ticking noise is common with most heaters. If the noise from your Thermablaster Heater is excessive, contact a qualified service technician.
Why is my Thermablaster Heater emitting smoke or odor during initial operation?
If you're experiencing a slight smoke or odor during the initial operation of your Thermablaster Heater, this problem should stop after a few hours of operation.
General| Model | WDFT250-VF-IR |
|---|---|
| Category | Heater |
| Voltage | 120V |
| Heating Technology | Infrared |
| Fan Included | Yes |
| Thermostat | Adjustable |
| Safety Features | Overheat Protection, Tip-Over Switch |
To Next Page
