Thermo Scientific ADVANCED Series

Other manuals for Thermo Scientific ADVANCED Series

Quick Start Guides96 pages

Questions and Answers

R
Richard FernandezAug 4, 2025
What to do if Thermo Scientific ADVANCED has inadequate temperature control?
- M
  Mia RossAug 4, 2025
  If you're experiencing inadequate temperature control with your Thermo Scientific Water System, consider the following: * Verify the setpoint. * For refrigerated baths, make sure the condenser is free of dust and debris. * Check the fluid concentration. * Ensure the circulator installation complies with the site requirements. * If the temperature continues to rise, ensure your application's heat load does not exceed the rated specifications. * Enter the controller menu and ensure the ENERGY SAVER mode is on in order for the system to maintain a stable temperature. * Check for high thermal gradients (e.g., the application load is being turned on and off or rapidly changing).
P
Patricia WhiteAug 9, 2025
Why Thermo Scientific ADVANCED Water System circulator will not start?
- L
  Lauren SanchezAug 9, 2025
  If your Thermo Scientific Water System circulator isn't starting, here are a few things to check: 1. Examine the display for any error codes. 2. Make sure the circuit protector(s) is in the on ( I ) position. 3. Confirm that the supply voltage is connected and matches the circulator's nameplate rating ±10%.
K
kerry16Aug 14, 2025
What to do if Thermo Scientific ADVANCED circulator shuts down?
- T
  Thomas MooreAug 14, 2025
  If your Thermo Scientific Water System circulator shuts down, here are some things to check: * Ensure the button wasn't accidentally pressed. * Ensure the circuit protector(s) is in the on ( I ) position. * Check the display for error codes. * Make sure the supply voltage is connected and matches the nameplate rating ±10%. * Restart the circulator.
J
John HartAug 18, 2025
What to do if Thermo Scientific ADVANCED Water System circulator will not circulate process fluid?
- G
  garrettchristopherAug 18, 2025
  If your Thermo Scientific Water System circulator isn't circulating process fluid, try these steps: * Check the reservoir level and fill if needed. * Inspect the application for any restrictions in the cooling lines. * If the pump motor overloaded, allow time for the motor to cool down. * Ensure the supply voltage matches the circulator's nameplate rating ±10%.
C
Christopher LoveAug 25, 2025
What to do if Thermo Scientific ADVANCED Water System display reads 239°C?
- E
  Emily WalkerAug 25, 2025
  If the display of your Thermo Scientific Water System reads 239°C, it might be because an external temperature probe is selected but not attached. Attach an external probe or select the internal temperature sensor.
K
Kendra MccormickAug 29, 2025
Why Thermo Scientific ADVANCED has no display?
- J
  James OwensAug 29, 2025
  If there is no display on your Thermo Scientific Water System, recycle the circuit protector on the rear of the circulator.

Summary

Preface

Compliance and WEEE

Details on product compliance with EC Directives and Waste Electrical & Electronic Equipment.

After-sale Support

Information regarding customer support and service for Thermo Scientific products.

Unpacking

Instructions for safely unpacking the unit and handling potential shipping damage.

Section 1 Safety

Safety Warnings

Crucial instructions and precautions for safe installation and operation of the unit.

Section 2 General Information

Product Specifications

Detailed technical specifications for ADVANCED, ARCTIC, SAHARA, and G 50 series bath circulators.

Wetted Materials

Lists materials that come into contact with the process fluid for various product series.

Section 3 Installation

Ambient Conditions and Ventilation

Guidelines for environmental conditions and air circulation requirements for proper unit operation.

Electrical Requirements

Specifications for power supply, voltage, and plug types for different unit models.

Tubing and Connections

Guidelines for selecting and installing tubing for external circulation and connecting ports.

Fluid Handling and Filling

Procedures and precautions for selecting, filling, and draining bath fluids.

Section 4 Operation

Thermostat Controls and Basic Operation

Overview of thermostat interface, start-up, status display, and setpoint adjustment.

Menu Navigation, Settings, and Editor Functions

Guide to accessing menus, configuring settings, and using editor functions for programs.

System Adjustments, Calibration, and Accessories

Information on adjusting control types, calibrating sensors, and configuring accessories.

Unit Shutdown Procedures

Instructions for properly stopping, powering down, and shutting off the unit.

Section 5 Accessories

Lifting Platform and Cooler Bridge Installation

Step-by-step instructions for installing lifting platforms and immersion cooler bridges.

Rack Assembly and Communications

Guidance on assembling racks and installing serial communication adapters.

Tubing Accessories

Catalog of available tubing types, lengths, and fittings for temperature control systems.

Section 6 Preventive Maintenance

Cleaning Procedures

Recommended methods for cleaning the bath vessel and internal components.

Testing Safety Features

Procedures for verifying high temperature protection and low liquid level safety functions.

Section 7 Troubleshooting

Error Displays and Faults

Explanation of error messages, safety faults, and troubleshooting steps.

Warning Displays and Other Errors

Information on warning messages, communication errors, and sensor issues.

Appendix Serial Communications

Terminal Settings and Syntax

Defines terminal settings and the general syntax for serial communication commands.

User and Optional Commands

Lists available commands for reading and writing parameters and controlling the unit.

RMA Form

Equipment Return Information

Details required for returning equipment, including description, reason, condition, and contamination.

Warranty