EasyManua.ls Logo

Thinkwater OSMO-MAXI STANDARD - User Manual

Default Icon
14 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Manuale Utente Osmomaxi ENG 2014-02-24 - 17 -
!
SAFETY WARNINGS
At the end of the day, close the water inlet valve
and disconnect the power plug.
In case of a water leak, disconnect the power plug
and close the water inlet valve, then contact the
service centre.
You should not open the machine cover.
For all operations of installation, extraordinary
maintenance, break down researches and spare
parts requests, please contact the manufacturer or
a qualified service centre.
Read carefully the instructions for installation,
operation and maintenance before installing this
equipment.
Improper installation, alterations or modifications
can cause damage to people and property.
Intentional damage or from negligence, or deriving
from the non-compliance with rules and
instructions, or due to incorrect connections or
unauthorized tampering, invalidate any warranty
or liability of the manufacturer.

Table of Contents

Questions and Answers

  • R
    Ronald Mills DVMAug 18, 2025
    What to do if the Thinkwater Water Filtration System display does not turn on?
    • O
      Olivia KnightAug 18, 2025
      First, ensure the plug is properly inserted and that there is an electricity supply. If that's not the issue, check if the board is in the “OFF” position and press the ON-OFF switch. If the display still doesn't turn on, it could be an internal electrical fault. In this case, unplug the system, turn the valve to the "By-pass" position, and contact the assistance service.
  • T
    Tina ContrerasAug 21, 2025
    Why does my Thinkwater Water Filtration System show “Alarm Leakage?”
    • A
      Alison MurphyAug 21, 2025
      The “Alarm Leakage” message indicates a leak. You can try to reset the alarm. However, if the alarm repeats, or if you notice water leakage, immediately close the upstream water supply valve, unplug the system, and contact the assistance service.
  • R
    Raymond JensenAug 23, 2025
    What to do if the Thinkwater Water Filtration System produces little water and shows "A1" alarm?
    • J
      Jaime GoodwinAug 23, 2025
      If your system is producing little water and the dishwasher displays an "A1" alarm, the filter might be clogged. Check the pressure downstream of the filter and replace it if necessary. Also, verify that the bypass valve is in the “OPEN” position. If the issue persists, unplug the system, turn the valve to "By-pass" and call the assistance service, as the pump, membranes or the solenoid valve might be damaged.
  • K
    Katrina ButlerAug 26, 2025
    Why does the Thinkwater Water Filtration System engine not start?
    • C
      cheryl24Aug 26, 2025
      If the display is on, the dishwasher opens the load solenoid valve, osmosis drains water but the engine won't start, it could be due to an engine fault. Unplug the system, turn the valve to "By-pass" and call the assistance service.
  • R
    Rachel BridgesAug 27, 2025
    What to do if my Thinkwater Water Filtration System displays "Alarm p. min” and stops?
    • I
      Isaac FisherAug 28, 2025
      If your system starts but then displays "Alarm p. min” and stops, check the following: 1. Ensure the upstream inlet water valve is open. 2. Verify the by-pass valve is in the OPEN position. 3. Remove any ¾ " attacks and transparent caps. 4. Check the inlet pressure upstream of the device. 5. Inspect the filter for clogs and replace if needed. 6. Ensure inlet water pipes are not bent or crushed. If the problem continues, unplug the system, turn the valve to "By-pass" and call the assistance service, as it could be a solenoid/faulty card issue.
  • K
    Karen BryantAug 30, 2025
    Why does the Thinkwater Water Filtration System operate discontinuously?
    • K
      Keith McdonaldAug 30, 2025
      If the system operates discontinuously, it might be due to the maximum pressure being set too low. In this case, unplug the system, turn the valve in "By-pass" and call the assistance service. Also, make sure that inlet water pipes are not bent or crushed.
  • M
    Marcus ReynoldsSep 1, 2025
    What to do if my Thinkwater Water Filtration System displays "Alarm High Cond "?
    • M
      michelle78Sep 1, 2025
      If the system displays "Alarm High Cond ", check the conductivity of the produced water and contact the service centre for the replacement of membranes, as they might be clogged or damaged.
  • A
    Amanda Howell MDSep 3, 2025
    Why does the Thinkwater Water Filtration System stop when the dishwasher isn't loading water?
    • A
      Amy ThompsonSep 3, 2025
      If the system stops when the dishwasher is not loading water, it could be due to a maximum pressure switch or wiring failure. In this case, unplug the system, turn the valve in "By-pass" and call the assistance service. Also, check if the in/out links were inverted.
  • J
    James GreenSep 6, 2025
    What to do if the Thinkwater Water Filtration System doesn't start during the dishwasher loading phase?
    • C
      Cathy WilliamsSep 6, 2025
      If the system doesn't start during the dishwasher loading phase, first remove any ¾ " attacks and transparent caps. Then, check if the in/out links were inverted. Also, ensure the by-pass valve is in the “OPEN” position. If the issue persists, unplug the system, turn the valve in "By-pass" and call the assistance service, as it could be a maximum pressure switch or wiring failure.
  • C
    csmithSep 8, 2025
    Why does the Thinkwater Water Filtration System water taste unpleasant?
    • M
      Matthew JohnsonSep 8, 2025
      If the treated water has an unpleasant taste, the filter might be used up. Replace the filter and then perform loading and unloading the dishwasher tank twice. If the issue persists, the equipment might be bacterially contaminated, so contact assistance service to perform the sanitization of the equipment.

Thinkwater OSMO-MAXI STANDARD Specifications

General IconGeneral
Stages5
TypeReverse Osmosis
Filter Lifespan6-12 months
Filter TypeSediment, Carbon Block, RO Membrane
Operating Temperature5-38°C