THOMAS DÖRR TD 3000L M14

Questions and Answers

S
Shannon BrownAug 14, 2025
What to do if granulate falls out of THOMAS DÖRR Sander?
- B
  Brooke PerezAug 14, 2025
  Granulate may fall out of the THOMAS DÖRR Sander for several reasons. If the granulate is too wet, its volume increases, causing it to escape through the screen holes. Ensure the specified heat-up period is observed to allow water to evaporate. Let cutlery drip dry before inserting it into the machine. If the machine was turned off immediately after polishing, let it run for 30 minutes to dry the granulate. Replace the granulate, considering the heating and drying procedures. If the issue persists, some granulate may need to be removed, or the axial fan may not be working correctly. Additionally, the spoon's form may contribute to granulate falling out.
B
brittneysanchezAug 18, 2025
What to do if granulate dust particles appear on cutlery from THOMAS DÖRR TD 3000L M14 Sander?
- A
  Amanda RasmussenAug 18, 2025
  If you notice granulate dust particles on the cutlery, it could be due to fresh granulate initially causing more dust deposits. Try heating up the granulate as required, then add 4-5 shot glasses of water into the machine's feed chute. Also, if the cutlery is smeary, causing granulate dust to stick, wash the cutlery by hand, rinse thoroughly, and reinsert it into the cutlery polisher. If the polishing results are good after doing so, then there was too much dishwashing detergent in the dishwasher. In that case, contact your dishwasher service technician to reduce the dishwashing detergent or rinsing agent dose.
J
jonathanmurphyAug 21, 2025
Why is my THOMAS DÖRR TD 3000L M14 cutlery not transported out of the machine?
- W
  william36Aug 21, 2025
  If the cutlery is not being transported correctly out of the machine, it may be due to an insufficient quantity of granulate. Replace the granulate with original Dörr polishing granulate, using exactly one filling. If this happens often, the granulate may be swelled up. In this case, switch off the machine, open the top cover and, if necessary, also the cover sheet, and remove the cutlery.
J
Jeffrey GarciaAug 25, 2025
What to do if granulate sticks to cutlery in THOMAS DÖRR TD 3000L M14?
- H
  hhendersonAug 25, 2025
  If granulate sticks to the cutlery, wash the cutlery again thoroughly and insert it into the machine again. If granulate pieces no longer stick to the cutlery then the problem was the dishwashing results. There may have been too much cutlery in the basket. Wash the cutlery by hand, rinse thoroughly, then insert it into the cutlery polisher again. If the polishing results are good then there was too much dishwashing detergent in the dishwasher. Contact your dishwasher service technician to reduce the dishwashing detergent or rinsing agent dose.
H
Holly MendozaAug 28, 2025
Why are polishing results poor with my THOMAS DÖRR TD 3000L M14 Sander?
- M
  Mario RayAug 28, 2025
  Poor polishing results may occur if dry cutlery is inserted; always ensure the cutlery is dripping wet. Check the granulate temperature by hand; it should be noticeably warm. The granulate should also be replaced every 4 to 8 weeks, depending on the daily operation hours.
M
Maria KellerAug 31, 2025
Why is my THOMAS DÖRR TD 3000L M14 Sander machine too loud?
- A
  Alexis WilsonAug 31, 2025
  If the machine is too loud, remove any cutlery pieces laying by the motor, springs, and cover sheet. Also, remove the transporting safety device. Ensure all screws are fastened; if not, tighten them.
R
Renee GarciaSep 3, 2025
What to do if my THOMAS DÖRR TD 3000L M14 machine does not start?
- D
  Derek GarciaSep 4, 2025
  If the machine does not start, ensure the top cover is closed and that the power plug is correctly inserted. Check the fuses.
S
Samantha CameronSep 6, 2025
What to do if UVC lamp does not switch on THOMAS DÖRR Sander?
- J
  Janet RamosSep 6, 2025
  If the UVC lamp does not switch on, it may be malfunctioning. Replace the UVC lamp.
S
Shawn SchultzSep 10, 2025
Why is the cutlery abnormally scratched by THOMAS DÖRR TD 3000L M14?
- E
  Elizabeth SchwartzSep 10, 2025
  If the cutlery is being abnormally scratched, ensure that the cutlery basket, where the cutlery pieces fall into, is placed directly underneath the ejection chute.