Need help?Do you have a question about the Tiesse Imola LX 0220 and is the answer not in the manual?
General| Type | Network Router |
|---|---|
| Wireless | No |
| Firewall | Yes |
| VPN Support | Yes (IPSec, PPTP, L2TP) |
| WAN Ports | 1 x RJ-45 |
| LAN Ports | 4 x RJ-45 |
| Weight | 0.5 kg |
| Power Supply | 12V DC |
Details configuration commands for Imola Ethernet interfaces (eth0, eth1).
Provides configuration commands for the Imola ISDN interface using dialer maps.
Covers the configuration of ADSL connections, bandwidth, and standards.
Details SHDSL interface configuration commands and standards.
Details configuration commands for the Frame Relay interface.
Details configuration for Imola mobile interface for GPRS sessions.
Details the configuration commands for the Wi-Fi interface.
Provides commands to activate, deactivate, and configure the hotspot function.
Details commands for configuring static routes with various parameters.
Details configuration of loopback addresses for router identification.
Shows how to display interface status, ARP, and routing tables using the ip command.
Details rules for accepting/rejecting IP packets and logging.
Explains how to modify source addresses of packets for NAT.
Details rules for traffic filtering using the filter table.
Covers NAT operations like SNAT, DNAT, and MASQUERADE.
Explains how to use DNAT for Port Forwarding and Load Balancing.
Details modifying IP or TCP header fields using the mangle table.
Describes common packet matching criteria and extensions.
Explains the different targets (actions) available in IPTables rules.
Covers advanced matching criteria and extensions for IPTables.
Details the configuration of VRRP protocol for virtual router redundancy.
Details RIP protocol configuration for network announcements and metrics.
Provides OSPF configuration commands for network interfaces and costs.
Details BGP protocol configuration for neighbor setup and network announcements.
Details PIM protocol for multicast routing, supporting Dense, Sparse, SSM modes.
Details GRE tunnel configuration parameters like name, IP, MTU, TTL.
Shows how to configure GRE tunnels using the create-tunnel command.
Details VPN IPSec configuration parameters for Phase I and Phase II.
Details static configuration for L2TPv3 tunnels and pseudo wire interfaces.
Explains how to create L2TPv3 tunnels dynamically.
Details configuration commands for Easy VPN tunnels.
Details how to configure traffic policies and bandwidth settings.
Explains how to create and configure traffic classes.
Describes how to assign traffic to classes using filters.
Explains how to activate or deactivate QoS rules.
Shows how to display QoS configuration, filters, and statistics.
Details TACACS+ configuration for authentication, accounting, and authorization.
Explains accounting and authorization functions for TACACS+.
Details RADIUS configuration for authentication and logging.
Details SNMP agent configuration including communities and traps.
Explains SNMPv3 user creation and access mode configuration.
Details how to activate and verify the Fprobe service.
Details configuration for local and remote Syslog services.
Details DLSW configuration for local and remote peers.
Details NTP configuration for system clock synchronization.
Details commands for configuring the Command Scheduler service.
Details DHCP server service configuration for LAN interfaces.
Details enabling antispoofing to block unauthorized traffic on an interface.
Details how to configure the router's time zone using CLI commands.
Explains the SIP Proxy service for VoIP on private LANs.
Describes SIP ALG (Application Level Gateway) functions.
Details how to register a user-ID to a SIP provider (registrar).
Provides ability to ring multiple phones cyclically for incoming calls.
Explains configuring triggers for interface activation/deactivation or events.
Details configuring triggers for backup status changes (e.g., remote address accessibility).
Defines criteria for verifying primary connection availability.
Details separating traffic between different interfaces using policy routing.
Explains configuring outgoing packets for round-robin transmission.
Illustrates configuring VRF-Lite for traffic separation between interfaces.
Details parameters for configuring RTR probes for performance measurement.
Shows how to display RTR service configuration, status, and statistics.
Explains creating and restoring configuration checkpoints.
Details downloading CLI commands from TFTP and uploading router configurations.
Provides steps for updating router software modules.
Lists CLI commands not automatically re-executed after router reboot.
Details DHCP server configuration for LAN interfaces and pools.
Shows how to assign IP addresses to switch ports in VLAN access mode.
Provides base configuration for ADSL NAT with public and private IPs.
Details base configuration for HDSL interface with private and public IPs.
Covers base GPRS configuration for public APN internet access with PAT.
Details GPRS configuration for private APN with GRE tunnel and keepAlive.
Base configuration for ISDN interface with dynamic IPs and NAT.
Base configuration for ISDN interface with static IPs and NAT.
Details base configuration for ADSL with GPRS backup.
Describes ADSL with GPRS backup, including SMS announcement.
Details QoS rules configuration for ADSL connections.
Details QoS rules configuration for HDSL connections.
Details SNMP agent configuration, communities, and traps.
Provides TACACS configuration details.
Details RADIUS server configuration for authentication.
To Next Page
