B
D
2.56 in / 65 mm - 3.5 in / 90 mm
“No-Go Zone”
“No-Go Zone”
“No-Go Zone”
Please remove any objects from the floor that may entangle the robot vacuum, such as pet
waste, socks, clothing, tissues, toys, slippery items, and power cords. You can utilize the provided
Cable Ties to organize your wires and power cords.
Since the robot can cross thresholds up to 0.7 in / 18 mm high, if any room's outer threshold is
less than 0.7 in / 18 mm, but the threshold measured from the inside of the room is higher than
0.7 in / 18 mm due to height differences, the robot may enter but not exit the room, potentially
becoming trapped. In such cases, set up a "No-Go Zone" or "Virtual Wall" for this room as
instructed on page 37 to prevent the robot from being trapped in this room.
1. Ensure that Bluetooth on your smartphone or
tablet is turned ON.
2. Ensure that the robot and your mobile device are
in close proximity to the router during the
connection process.
3. Ensure that your smartphone or tablet is connected to a 2.4GHz Wi-Fi
network.
4. If your router is a dual-band 2.4GHz/5GHz router, select the 2.4GHz
network.
5. If both bands use the same Wi-Fi name in your router, rename the
2.4GHz network on the router's control page and connect your mobile
phone to this newly named 2.4GHz network.
— Always keep the charging station plugged in to ensure the robot can
automatically return to recharge when the battery level is low.
— Clear objects within 1.6 ft / 0.5m of the left and right sides, and within
4.9 ft / 1.5 m in front of the Charging Station.
— Recommend to use adhesive tapes to fix Charging Station on the ground.
No matter when robot is cleaning or mapping, you could stop robot and set “No-Go Zone”,
“No-Mop Zone” or “Virtual Wall” in Tuya smart APP “Restricted Zone Setting” as you want, then let the
robot continue cleaning.
No-Go Zone (Max 7): To prevent Robot enter this zone in any time. For some place where robot
couldn’t clean, or don’t want robot enter in, or somewhere robot is easily stuck or trapped. Examples
are as below.
No-Mop Zone(Max 7): Special for Carpet areas. When Robot installs Mopping cloth holder, Robot
can't enter this zone to mop.
Virtual Wall (Max 20): Robot can't go cross virtual Wall.
Enter “Map Edit” in APP to merge, split rooms and rename each room to make sure the whole map is
same as your house layout.
Step 4: Enter “Map Management” to save current map
When the current map is lost or corrupted for some reason, you can use a saved map from the list of
Map Management."
During the initial cleaning, ensure that each room's door is open to assist the robot in fully
exploring your house.
A. Children's playroom: where have too
many toys on the ground, robot easily gets
stuck in this place.
B. Bathroom: Where there is too much water
on the ground, and robot would be damaged
by water.
C. Certain Room: There are high steps in
some places, and the robot can’t get out once
it goes in. Robot is trapped.
D. Some furniture: Where robot would easily
get stuck because its height exceeds the
bottom height of certain furniture.
Press and hold and
buttons on the robot at the
same time for 3 seconds,
Robot will say “Wi-Fi reset,
ready for Wi-Fi connection”,
and Wi-Fi Status Light will
Fast Flash.
3
4
5
Open Tuya Smart App,
Tap “Add Device” or “+”
at the upper right corner.
1
Search for Tuya Smart on
the App Store/Google
Play, or scan the QR code
above to download and
install it on your mobile
device.
Robot is discovered,
then tap "Add" button.
Select the same router's
2.4GHz Wi-Fi as mobile
phone and enter the
correct password.
Tap ”Next”.
Connecting to Wi-Fi.
Robot will say
“Connecting to Wi-Fi”.
Connection successful,
and Robot will say “Wi-Fi
Connection Successful”, and
Wi-Fi Status light will be solid.
7
6
8
Register and log in on
the app.
2
Wi-Fi Only
2.4GHz
1 2
3 4
5
Notes:
Please ensure your robot is fully charged before its first use. Attach Robot to the
Charging Station by aligning its Charging Contacts with the Charging Contacts
on the Charging Station. Once the robot is successfully connected to the
charging station, the voice prompt, “Start charging”.
Notes:
If fail to connect Wi-Fi in Quick
Mode as above, please try Wi-Fi
connecting in AP Mode,
details please check
"3.4.4.2 Connect Wi-Fi with AP
Mode" on user manual at page
20.
Notes:
Please search “Tikom Technology” in YouTube to find installation videos.
Notes:
Charging: Flash Blue
Full Charged: Solid Blue
1. 2. 3.
4. 5. 6.
7. 8.
Low Battery: Solid Red
L8K Pro_EN_V1.0
Customer Service: support.us@tikom.com
Re
m
ov e
Remove
1
2
21
21
Front Bumper
Laser Distance Sensor (LDS)
Wi-Fi Status Light & Reset Button
ON :Wi-Fi Connected
Flash :Wi-Fi not connected
Off :Sleep Mode or Power off
Reset robot : Use a needle
to press this Wi-Fi LED Status Light
Clean/Power Button
Power on or Power off Robot :
Press and hold this button 3s.
Start/ Stop Cleaning :Short press this button.
Home Button
Return to Charging Station :
Short press this button.
Reset Wi-Fi :
Press and hold and buttons for 3s in the same time.
Robot Status Light
SolidBlue :FullCharged(OnChargingstation)/
Normal(NotonChargingstation)
FlashBlue :Charging(OnChargingstation)
SolidRed :LowBattery
FlashRed :Abnormal
Off :Power Off or Sleep Mode
Installation Video
Release Button of Dust Bin
Dust Outlet Port to
Self-Empty Base
Dust Bin & Water Tank
Release Button of Mopping
Cloth Holder
Mopping Cloth Holder
Charging Contacts on Dust Bin
(For Self-Empty Base)
5
＜
0.7 in
＜
0.7 in
1
32
＞0.7 in / 18 mm
＜0.7 in / 18 mm
C
“No-Go Zone”
To Next Page
Need help?
General
