Titan Attachments PRO Series

Questions and Answers

A
Anthony BellAug 15, 2025
Why is the driveline clutch slipping on my Titan Attachments PRO?
- S
  Samantha WagnerAug 15, 2025
  The driveline clutch on your Titan Attachments Cutter might be slipping due to several reasons: * Scalping the ground: Raise the cutting height. * Cutting too fast: Reduce travel speed. * Power take-off being engaged too fast at high engine RPM: Slowly engage the power take-off at low engine RPM. * Cutting over solid objects: Avoid solid objects. * Clutch spring not set correctly: Check the dimension for spring setting on the clutch.
A
Amy AdamsAug 18, 2025
What to do if oil is leaking from my Titan Attachments Cutter?
- S
  Spencer BartlettAug 18, 2025
  If you notice oil leaking from your Titan Attachments Cutter, it could be due to: * The gearbox being overfilled: Drain to the side plug hole. * Damaged seals: Replace the seals. * Grass or wire wrapped on the shaft in the seal area: Check seal areas daily.
L
lbauerAug 22, 2025
What causes excessive wear on Titan Attachments Cutter blades?
- J
  John SmithAug 22, 2025
  Excessive wear on the blades of your Titan Attachments Cutter can be caused by: * Cutting on sandy ground: Raise the cutting height. * Contacting the ground frequently: Raise the cutting height.
R
Richard JacksonAug 26, 2025
What causes a driveline yoke or cross to fail on a Titan Attachments PRO Cutter?
- S
  srichardsonAug 26, 2025
  The driveline yoke or cross on your Titan Attachments Cutter may fail due to: * Shock load: Avoid hitting solid objects. * Lack of lubrication: Lubricate every 8 hours.
M
Mark MorganAug 28, 2025
What causes the driveline telescoping tube to fail on a Titan Attachments PRO Cutter?
- T
  Tina YorkAug 28, 2025
  The driveline telescoping tube might fail on your Titan Attachments Cutter because of: * Lack of lubrication: Lubricate every 20 hours. * Shock load: Avoid hitting solid objects.
K
Kevin BennettAug 31, 2025
Why are the blades breaking on my Titan Attachments Cutter?
- J
  Jimmy HuynhAug 31, 2025
  Blades on your Titan Attachments Cutter may break due to hitting solid objects. To prevent this, avoid hitting solid objects.
M
Mr. Ryan Palmer MDSep 4, 2025
How to prevent driveline bending on my Titan Attachments PRO?
- J
  Jennifer PeckSep 4, 2025
  To prevent driveline bending on your Titan Attachments Cutter: * If it's contacting the frame: Reduce the lift height in transport position. * If it's contacting the drawbar: Reposition the drawbar. * If it's bottoming out: Shorten the driveline.
M
Michael JensenSep 7, 2025
Why are the blades coming loose on my Titan Attachments PRO Cutter?
- S
  stewartvictorSep 7, 2025
  The blades on your Titan Attachments Cutter might be coming loose because: * The blade does not tighten properly: Tighten blade hardware (refer to “CUTTING BLADE MAINTENANCE” ON PAGE 32.) * Not using a new locknut when replacing blades: Use new locknuts.
S
Samantha KeySep 12, 2025
What causes the driveline telescoping tube to wear on a Titan Attachments PRO Cutter?
- B
  Benjamin GomezSep 12, 2025
  The driveline telescoping tube on your Titan Attachments Cutter may wear due to a lack of lubrication. Make sure to lubricate every 20 hours.