maintain that setting utilizing a 4% differential or deadband. At 70% RH in the humidify mode,
the equipment will be activated at 68% RH, and will deactivate at 72% RH. In the dehumidify
mode, with the setting at 70% RH, the equipment will activate at 72% RH, and deactivate at
68% RH. This differential allows your equipment to perform at an optimum level with minimum
cycling and reduces stress to your equipment.
The switch on the bottom right of the controller is used to determine whether it will be used in
the “Humidify” mode or the “Dehumidify” mode.
The Eos 1 provides up to 15 amps of capacity on a standard 120 volt circuit. The Eos 1 is built
with the highest quality components and will provide the user with years of trouble free service.
Instructions for Operation
• Securely mount your Eos 1 in your enclosure and away from any spray/water/mist, etc.
• Set the “Humidify/Dehumidify” switch to activate your equipment at preferred setting.
• Plug your equipment into the female side of the piggyback cord set.
• Adjust your equipment (humidifi er, dehumidifi er or fan) to highest setting on the dial.
• Verify that the equipment to be activated is turned “ON”
• Plug the male side of the piggyback cord set into a 120 volt / 15 amp outlet. Use of a surge
protection power strip is recommended.
• Your Eos 1 will now control your equipment at the desired settings until the power is defeated.
• To reset your Eos
1. Simply unplug the piggyback cord from the 120 volt outlet, adjust your settings,
and plug it back into the 120 volt outlet to activate controller at new settings
Troubleshooting Tips
If the Eos 1 is not performing as expected, try the following:
a. Confi rm that your power input is active and providing 120 volts/ 15 amps
to the controller.
b. Check the voltage output of your piggyback cord set using a voltage test meter,
fan or 120 volt light to verify power is fl owing through controller when activated.
c. Make sure that your “Humidifi cation/Dehumidifi cation” switch is in the correct
mode for your application.
d. If your Eos 1 is not functioning in the correct mode, check the vents to see if there
are any obstructions or impediments covering them. If so, clean the vents using
warm water on a soft cloth. Allow unit to completely dry before using.
e. Should you fi nd that your Eos 1 is not activating your equipment, verify that your
setting on the controller is correct and that the power switch on your equipment is
“on” and at the highest setting.
f. If you’re still having problems with your Eos 1, please contact our Technical Service
Representative to assist you further.
Warranty Information
• Titan Controls warrants the original purchase of this product against defects in material and
workmanship under normal use for three (3) years from the date of purchase.
• During the warranty period, Titan Controls will, at our option, and without charge, repair or
replace this product if the controller or any of its components fail or malfunction.
• All returns or repairs must be accompanied by a Return Merchandise Authorization (RMA)
number prior to any service of the product.
• This warranty is expressly in lieu of all other warranties, expressed or implied, including the
warranties of merchantability and fi tness for use and of all other obligations or liabilities on the
part of the seller.
• This warranty shall not apply to this product or any part thereof which had been damaged by
accident, abuse, misuse, modifi cation, negligence, alteration or misapplication.
• Controllers with serial numbers or date tags that have been removed, altered or obliterated;
broken seals or that show evidence of tampering; mismatched board serial numbers or
nonconforming parts, are excluded from coverage.
• Titan Controls makes no warranty whatsoever in respect to accessories or parts not
supplied by Titan Controls.
• Monetary refunds of the warranty will not be given.
• The Buyer assumes all responsibility regarding the use & installation of this controller.
• All warranty service is provided through the factory or an authorized service representative.
• This warranty shall apply only to the United Sates, including Alaska, Hawaii and territories of the
United States.
• Defective controllers need to be returned with the “proof of purchase/receipt”.
• For additional warranty information, contact a Titan Controls Technical Service Representative or
your Dealer.
• NOTE: Titan Controls is a manufacturer of environmental controls. All sales offerings to the
public are done through a nationwide group of Dealers. No sales offerings will be made directly
to the general public.
Service and Repair Program
• For all service and repairs please contact one of our Technical Service Representatives for a
Return Merchandise Authorization (RMA) number.
• All factory service & repairs will be completed within 48 hours of receipt of controller and after
authorization by customer for repairs.
• Titan Controls will, at its discretion, repair or replace the controller.
• Factory calibration services are available for all Titan Controls.
• Returning Units: Please contact your retail store for returns.
To Next Page
Loading...
Need help?
General