Titan Implement 1800 Series

Questions and Answers

M
Mary WallsAug 19, 2025
How to fix uneven cut with Titan Implement 1800?
- O
  ogoodwinAug 20, 2025
  If your Titan Implement Farm Equipment is producing an uneven cut, there are several potential causes. You might be operating at an excessive ground speed, so try reducing your speed. The blades could be worn, dull, or bent, in which case you should replace them. Check the height adjustment; it may need to be adjusted according to the instructions. Low tire pressure on one side of the tractor can also cause this issue, so adjust the tire pressure as needed. Reduce ground speed when turning. Adjust your tractor wheel spacing. A damaged cutter pan could also be the culprit, requiring repair or replacement.
D
David WoodsAug 21, 2025
What to do if material discharges unevenly from Titan Implement Farm Equipment?
- P
  pwilliamsAug 21, 2025
  If the material is discharging unevenly from your Titan Implement Farm Equipment, resulting in bunches along the swath, it could be due to several factors. If the material is too high or there is too much of it, reduce ground speed while maintaining 540 RPM at the tractor PTO, or make two passes, raising the rotary cutter for the first pass and lowering it for the second, cutting at a 90° angle to the first pass. Raising the rear of the rotary cutter may also help, but be careful not to raise it so high that it causes other issues. If the grass is wet, allow it to dry before mowing and slow down the tractor while keeping the engine at full PTO RPM. The rear of the rotary cutter might be too low, trapping material, so adjust the cutter height and attitude accordingly.
J
James MahoneyAug 25, 2025
Why is my Titan Implement 1800 leaving uncut material?
- D
  Donald ChristensenAug 25, 2025
  If your Titan Implement Farm Equipment is leaving uncut material, it may be due to excessive ground speed, so reducing it should help. Also, ensure that you are maintaining the correct RPM; keep the PTO speed at 540 RPM.
A
Andrew PriceAug 26, 2025
Why is the gearbox leaking on my Titan Implement Farm Equipment?
- K
  Kathryn JoyceAug 26, 2025
  If your Titan Implement Farm Equipment's gearbox is leaking, there are several possible causes. The oil seal might be damaged and need replacement. A bent shaft could also be the issue, potentially requiring a gearbox replacement. Ensure the oil seal is properly sealing in the housing; if not, replace the seal or use a sealant on the outside. If the oil level is too high, drain it to the correct level. A damaged gasket should be replaced, and loose bolts need to be tightened.
D
Dana BerryAug 27, 2025
Why is my Titan Implement 1800 Farm Equipment vibrating excessively?
- D
  davismichelleAug 28, 2025
  If you're experiencing excessive vibration with your Titan Implement Farm Equipment, it could be because the blades are not swinging freely; check the bushing and blade movement. Another possibility is that the blades are out of balance, so inspect them for damage or consider replacing them.
A
Aaron FerrellAug 29, 2025
Why is my Titan Implement Farm Equipment windrowing?
- W
  wendy60Aug 29, 2025
  If your Titan Implement Farm Equipment is windrowing, it could be because the material is heavy and lush. Try raising the front of the rotary cutter relative to the rear. Excessive ground speed can also cause this, so reduce your speed. If conditions are too wet, wait for them to dry and reduce ground speed.
T
Tony MeyerAug 31, 2025
Why is the gearbox overheating on my Titan Implement 1800?
- Y
  ysawyerAug 31, 2025
  If your Titan Implement Farm Equipment's gearbox is overheating, it may be low on lubricant; fill it to the level plug. It could also be due to an improper type of lubricant, in which case you should replace it with the correct one. Excessive trash build-up around the gearbox can also cause overheating, so remove any debris.
R
Rebecca VasquezSep 2, 2025
What causes unusual noise in Titan Implement 1800 Farm Equipment?
- M
  Michael VangSep 3, 2025
  If your Titan Implement Farm Equipment is making unusual noises, it could be due to loose blade bolts or worn bushings; tighten the bolts and check the bushings for wear, replacing them as needed. A bent blade carrier or blades can also cause this, so replace the blade carrier. If the deck is bent, causing the blades to contact it, straighten the deck.
W
wlindseySep 5, 2025
Why won't the driveline telescope on my Titan Implement 1800?
- P
  Preston RogersSep 5, 2025
  If the driveline on your Titan Implement Farm Equipment will not telescope, it could be due to improper lubrication; grease the driveline. A twisted driveline will need to be replaced, and be cautious not to strike the ground with the blades. A bent driveline, possibly from being too long, should also be replaced and shortened to the proper length. Damaged shields should be replaced as well.
U
urobinsonSep 6, 2025
Why does Titan Implement 1800 cut grass lower in center of swath than at edge?
- T
  tommywheelerSep 6, 2025
  If your Titan Implement Farm Equipment is cutting grass lower in the center of the swath than at the edge, it's likely because the height of the rotary cutter is lower at the rear or front. Adjust the rotary cutter height and attitude so that the rear and front are within 1/2” of the same height.

Summary

Pre-Delivery Checklist

Lubrication and Hydraulics

Checks for gearbox lubricant and grease points.

Cutter Checks

Checks for cutter bolts, blades, and hardware.

Tractor Connections

Ensures proper hitch pin and clevis installation.

Safety Items

Checks for safety decals, shields, and manuals.

Introduction

Welcome

Welcomes user and introduces the rotary cutter.

Safe Operation

Emphasizes reading the manual for safe operation.

Safety Shields

Stresses the importance of keeping safety shields in place.

Safety

General Safety

Discusses operator responsibility and accident prevention.

Safety Alert Symbols

Explains hazard warning symbols and signal words.

Safety Icon Nomenclature

Defines pictorial icons for hazards and safety measures.

General Safety Instructions

Reinforces operator responsibility and general safety practices.

Personal Protection Equipment

Lists recommended PPE for safe operation.

Training Requirements

Covers user training and OSHA requirements.

Federal Laws and Regulations

Outlines relevant OSHA and legal requirements.

Safety Signs and Labels

General Information

Introduces safety signs and their importance on the equipment.

Installing Replacement Signs

Provides instructions for applying new safety decals.

Safety Sign Locations

Shows where safety signs are placed on the cutter.

Nomenclature

Description and Intended Use

Describes the rotary cutter and its intended applications.

Parts Identification

Identifies all parts of the rotary cutter with a diagram.

Assembly

Tools Required

Lists necessary tools for assembly.

Assembly Procedure

Step-by-step guide for assembling the cutter.

Driveline Installation

Instructions for connecting the driveline to the tractor PTO.

Driveline Length Checks

Procedures for checking and adjusting driveline length.

Operation

User Safety Training

Refers to safety instructions for operators.

Tractor Requirements

Specifies tractor features needed for safe operation.

Attaching to Tractor

Step-by-step guide to connect the cutter to the tractor.

Detaching from Tractor

Step-by-step guide to disconnect the cutter from the tractor.

Setting the Rotary Cutter

Adjusting pitch and cutting height for optimal performance.

Initial Setup Checklist

A checklist for first-time use and setup.

Pre-Operation Checklist

Essential checks before each use.

Operating Safety

Critical safety points during operation.

Transporting

Transporting Safety (Road)

Safety instructions for transporting the cutter on roads.

Storage

Storage Safety

General safety precautions for storing the cutter.

Placing and Removing from Storage

Procedures for storing and retrieving the cutter.

Service and Maintenance

Maintenance Safety

General safety precautions for maintenance tasks.

Greasing and Lubrication

Instructions for greasing and lubricating various components.

Blade Servicing

Procedures for blade inspection, sharpening, and replacement.

Slip Clutch Checks and Adjustments

How to check and adjust the slip clutch.

Bolt Torque Requirements

Explains proper bolt torque and provides a chart.

Troubleshooting

Common Cutting Issues

Solutions for uneven cuts, uncut material, and windrowing.

Gearbox and Driveline Problems

Solutions for gearbox noise, leaks, and driveline issues.

Specifications

Model Specifications

Lists technical details for different cutter models.

Gearbox Warranty

Warranty period for gearboxes.

Warranty

Limited Warranty

Details the limited warranty terms and conditions.

Parts

Hitch Assembly

Lists parts for the hitch assembly.

Deck Assembly

Lists parts for the deck assembly.

Tailwheel Assembly

Lists parts for the tailwheel assembly.

Leveling Rods

Lists parts for the leveling rods.

Hydraulic System

Lists parts for the hydraulic system.

Driveline Components

Lists parts for the driveline assembly.

Blade Assembly

Lists parts for the blade assembly.

Gearbox Components

Detailed breakdown of gearbox components.