EasyManua.ls Logo

Titan Lifts SL-6600 - User Manual

Titan Lifts SL-6600
30 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
INSTALLATION, OPERATION
& MAINTENANCE MANUAL
FOLLOW THIS MANUAL CAREFULLY TO ENSURE THE EQUIPMENT WILL
FUNCTION CORRECTLY AND PROVIDE MANY YEARS OF DEPENDABLE SERVICE.
FAILURE TO FOLLOW THESE INSTRUCTIONS AND SAFETY WARNINGS MAY
RESULT IN PERSONAL INJURY OR PROPERTY DAMAGE. KEEP THIS MANUAL IN A
SAFE DRY PLACE FOR FUTURE REFERENCE.
®
MODEL:
SL-6600
6,600 LB CAPACITY SCISSOR LIFT

Table of Contents

Questions and Answers

  • K
    Kyle JohnsonAug 11, 2025
    What to do if Titan Lifts SL-6600 platforms go down slowly?
    • V
      vmillerAug 11, 2025
      If your Titan Lifts Scissor Lifts platforms descend slower than expected after being raised, several factors could be at play. The oil hose might be leaking, necessitating a check or replacement. Alternatively, the oil cylinder might not be properly tightened, suggesting a seal replacement. Other potential causes include leaks in the single valve, overflow valve, or electrical unloading valve, each requiring cleaning or replacement to resolve the issue.
  • A
    Ashley WilliamsAug 16, 2025
    Why are Titan Lifts SL-6600 Scissor Lifts raising too slow?
    • K
      Kimberly MartinAug 16, 2025
      If your Titan Lifts Scissor Lifts are raising too slowly, there are several potential causes. The oil filter may be clogged, requiring cleaning or replacement. Insufficient oil levels could also be the issue, so add oil as needed. Additionally, the overflow valve might not be correctly adjusted, so ensure it's in the right position. Overheated hydraulic oil (above 45°C) can also cause slow raising, necessitating an oil change. Finally, a worn cylinder seal could be the culprit, requiring replacement.
  • J
    jamesfergusonAug 22, 2025
    What to do if Titan Lifts SL-6600 Scissor Lifts motor runs but will not raise?
    • R
      Robert LozanoAug 22, 2025
      If the motor of your Titan Lifts Scissor Lifts runs, but the lift won't raise, several issues could be the cause. First, the motor might be running in reverse, so check the wire connection. The overflow or cushion valve could be loose or jammed, requiring cleaning or adjustment. A damaged gear pump would need replacement. Low oil levels require adding oil. A loose or detached oil hose needs tightening. Addressing these points should help resolve the issue.
  • P
    pcohenAug 29, 2025
    How to fix Titan Lifts SL-6600 Scissor Lifts lowering too slow?
    • A
      andersoncaitlinAug 29, 2025
      If your Titan Lifts Scissor Lifts are lowering too slowly, it could be due to several reasons. The throttle valve might be jammed, so try cleaning or replacing it. If the hydraulic oil is dirty, changing it could solve the problem. A jammed anti-surge valve would need cleaning. Lastly, a jammed oil hose would require replacement.
  • A
    aarongraySep 3, 2025
    Why Titan Lifts SL-6600 Scissor Lifts motor does not run and will not raise?
    • K
      Kelli SmithSep 3, 2025
      If the motor of your Titan Lifts Scissor Lifts does not run and the lift won't raise, it could be due to a loose wire connection. Check the wire connection and ensure it is secure. Alternatively, the motor may be burnt, in which case it needs replacement.

Titan Lifts SL-6600 Specifications

General IconGeneral
BrandTitan Lifts
ModelSL-6600
CategoryScissor Lifts
LanguageEnglish