TLW VEW K10-1220Z - User Manual

Product Name: SMART DRIVER 15W 12V LED Smart Driver
With 6-Port Micro Plug Connector
Product Code: K10-1220Z
Kit Contents
▪ Smart LED Driver with 6-port micro plug connector
Important Safety Information
DISCLAIMER: PLEASE NOTE LED DRIVER INSTALLATION SHOULD BE CARRIED OUT
BY A QUALIFIED ELECTRICIAN!
Do not install with power applied to device
Do not expose the device to moisture
Installation
1
2
1 metre power lead needs to be wired
to a 240V power supply
Plug in LED light power
lead to connector block

Summary

Important Safety Information

General Safety Precautions

Critical warnings for installation and operation by qualified personnel, avoiding moisture and live power.

Installation Overview

Function Introduction

Explains the basic operation and connection points of the LED driver.

Installation Details

Wiring Diagram

Illustrates the electrical connections for the LED driver.

Manual Factory Reset

Step-by-step instructions to perform a factory reset on the device.

Product Specifications and Features

Technical Specifications

Detailed technical specifications including voltage, power, dimming, and environmental ratings.

Product Features and Compliance

Highlights key features, safety standards, EMC compliance, and physical dimensions.

Overview

1. Function Description
2. Important Technical Specifications
3. Usage Features
4. Maintenance Features

The SMART DRIVER 15W 12V LED Smart Driver with 6-Port Micro Plug Connector, product code K10-1220Z, is a ZigBee dimmable LED driver designed for indoor LED lighting applications. This device acts as a wireless receiver, communicating with and controlled by various ZigBee compatible systems via radio signals.

Function Description:

The primary function of this smart driver is to power and control single-color LED lights. It enables users to control the ON/OFF state and adjust the light intensity of connected LED lights. The dimming is achieved through Pulse Width Modulation (PWM) and offers a deep and smooth dimming range from 0.1% to 100%.

The device features a 6-port micro plug connector for easy connection of LED lights. It includes a "Prog. key" which serves multiple purposes: a short press can switch the connected load on or off, while pressing and holding down the key allows for increasing or decreasing the light intensity.

For connectivity, it is a ZigBee end device that supports Touchlink commissioning, allowing it to directly pair with compatible ZigBee remotes. It is also compatible with universal ZigBee gateway products and universal ZigBee dim remotes, offering broad integration into existing smart home ecosystems.

Important Technical Specifications:

• Product Name: SMART DRIVER 15W 12V LED Smart Driver With 6-Port Micro Plug Connector
• Product Code: K10-1220Z
• LED Channel: 1
• DC Voltage Output: 12V
• Max Current Output: 1.25A
• Rated Power: Max 15W
• Voltage Tolerance: ±1%
• Input Voltage Range: 200-240V AC
• Frequency Range: 50/60Hz
• Power Factor: >0.9 @ 230VAC
• Total Harmonic Distortion (THD): ≤15% (@full load/230V AC)
• Efficiency: 85% @230V AC full load
• AC Current: 0.09A @230V AC
• Leakage Current: <0.5mA/ 230V AC
• Dimming Interface: ZigBee
• Dimming Range: 0.1%-100%
• Dimming Method: Pulse Width Modulation
• Over Current Protection: Yes, recovers automatically after fault condition is removed.
• Over Temperature Protection: Yes, recovers automatically after fault condition is removed.
• Working Temperature: -20°C to +45°C
• Maximum Case Temperature: 85°C (Ta=”45°C)
• Working Humidity: 10%-95% RH non-condensing
• Storage Temperature and Humidity: -40°C to +80°C, 10%-95% RH
• Safety Standards: ENEC EN61347-1, EN61347-2-13 approved
• Withstand Voltage: I/P-O/P: 3.75KVAC
• EMC Emission: EN55015, EN61000-3-2, EN61000-3-3
• EMC Immunity: EN61547, EN61000-4-2,3,4,5,6,8,11, surge immunity Line-Line 0.5KV
• MTBF: 190500H, @ 230VAC at full load and 25°C ambient temperature
• Dimensions: 1784622 mm (LWH)
• Waterproof Grade: IP20
• Construction: Class II power supply, full isolated plastic case, built-in active PFC function.

Usage Features:

The SMART DRIVER is designed for ease of use and integration into smart lighting systems.

• Simple Wiring: A 1-meter power lead needs to be wired to a 240V supply, and LED light power leads plug directly into the connector block.
• ZigBee 3.0 Protocol: Based on the ZigBee 3.0 protocol, ensuring compatibility with a wide range of ZigBee devices and systems.
• Touchlink Commissioning: Supports direct pairing with compatible ZigBee remotes without requiring a gateway.
• Broad Compatibility: Works with universal ZigBee gateway products and universal ZigBee dim remotes.
• High Power Factor and Efficiency: Contributes to energy savings and stable operation.
• Smooth Dimming: Provides deep and smooth dimming down to 0.1%, allowing for precise control over light ambiance.
• Indoor Use: Suitable for various indoor LED lighting applications.

Maintenance Features:

• Qualified Electrician Required: Installation should be carried out by a qualified electrician to ensure safety and proper setup.
• Safety Precautions: Do not install with power applied to the device and do not expose the device to moisture.
• Automatic Recovery: Features built-in over-current and over-temperature protection, allowing the device to automatically recover after fault conditions are removed, minimizing the need for manual intervention in case of minor issues.
• Factory Reset: The device can be manually reset to factory settings by pressing the "Prog. key" 5 times continuously or by re-powering the device 5 times continuously. A successful reset is indicated by the connected light blinking 3 times. This feature is useful for troubleshooting or reconfiguring the device.

TLW VEW K10-1220Z Specifications