EN | Quick Start Guide
CLEANING, STERILISING AND ASSEMBLY
Before first use disassemble and place all components in
boiling water for 5 minutes. This is to ensure hygiene.
1. Disassemble your bottle.
2. Wash all parts in warm soapy water and rinse or use a
dishwasher (top shelf only).
Ensure the lid of the venting tube ( is open.
3. Use a teat brush to gently clean the teat , do not turn
inside out as you may damage it.
4. Reassemble the teat
C and screw ringC and then place
all parts in boiling water for 5 minutes or use another
method of sterilisation such as a UV or steam steriliser or
cold water tablet/liquid solution
(ensure you follow the manufacturer's instructions).
5. After sterilising reassemble your bottle as per the diagram
ready for use. When assembling your bottle it is
important that you check the lid of the venting tubeC is
fully closed. You can do this by pressing the centre of the
lid with your thumb.
6. To prevent the teatC from collapsing, check that the slit
in the silicone valveC has not sealed. If it has sealed
pinch it gently between your fingers to ensure it's open.
SELF-STERILISING IN A MICROWAVE
This method allows you to easily sterilise bottles using a
microwave. Before self-sterilising, always disassemble and
wash all components thoroughly and rinse in clear water or
use dishwasher (top shelf only).
1. Assemble the teat
in the screw ringC and click the
bottle hoodC in place.
2. Pour exactly 50ml of water into the bottle baseC .
The bottles have a 50ml measureC .
3. Assemble the venting tubeC with the silicone valveC ,
and then place in the bottle baseC as per the diagram.
Ensure the lid of the venting tube is fully closed. You
can do this by pressing the centre of the lid with your
thumb. Ensure the inside of the venting tube is
thoroughly washed and dried before self-sterilising.
click!
B
B
D
E
D
G
G
E
F
B
B
A
H
E
E
E
F
1 2 3
4 5 6
1 2 3
4 5 6
4. Rest the assembled hood , teat , and screw ring
on top of the bottle base . Do not tighten on to base.
5. Place in the microwave for 3 minutes.
To sterilise multiple bottles see table below.
Allow the bottles to cool down for at least 5 minutes
before removing from microwave.
For glass bottles allow 30 minutes to cool down with the
microwave door open.
6. Pour out residual water and screw the assembled hood
, teat , and screw ring on to the bottle base
ready for use. Ensure the lid of the venting tube is
closed.
After the self-sterilisation the bottle and teat will remain
sterile for 24 hours if the bottle is unopened and fully
assembled.
Always store the bottles fully assembled.
7. To prevent the teat from collapsing, check that the slit
in the silicone valve has not sealed. If it has sealed
pinch it gently between your fingers to ensure it's open.
Microwave recommended times for all bottle sizes.
Based on microwaves from 700 to 1000 Watts.
STORAGE AND USE
• Inspect before each use and pull the feeding teat in all
directions.
• Always clean and sterilise before each use.
• Keep away from solvents or harsh chemicals.
• Do not allow the product to come into contact with oil
based foods.
• Not suitable for use in a conventional oven or a
combination microwave oven with the grill feature
switched on.
• Do not leave a feeding teat in direct sunlight or heat, or
leave in disinfectant (“sterilising solution”) for longer than
recommended, as this may weaken the teat.
• Teats are recommended to be replaced at least every
2 months for safety and hygiene reasons.
• Please dispose of this product and packaging responsibly.
FOR YOUR CHILD'S SAFETY AND HEALTH
WARNING!
• Always use this product with adult supervision.
Accidents have occurred when babies have been left
alone with drinking equipment due to the baby falling or if
the product has disassembled.
• Never use feeding teatss as a soother.
• Continuous and prolonged sucking of fluids will cause
tooth decay. Tooth decay in young children can occur
even when non-sweetened fluids are used. This can occur
if the baby is allowed to use the bottle for long periods
through the day and particularly through the night, when
saliva flow is reduced or if it is used as a soother.
• Always check food temperature before feeding. Heating in
microwave oven may produce localized high
temperatures. Take extra care when microwave heating.
Always stir heated food to ensure even heat distribution
and test the temperature before serving.
• Throw away at the first signs of damage or weakness.
• Keep components not in use out of the reach of children.
• Never attach to cords, ribbons, laces or loose parts of
clothing. The child can be strangled.
• Glass bottles may break.
• Do not heat in a microwave with bottle sealed.
• When making up feed, follow the formula milk
manufacturer's instructions.
• The bottle hood can pose a suocation hazard - keep out
of reach of children.
B
B
D
D
A
A
B
G
F
E
G
Number of bottles 1 2 3 4 5
Sterilising time (min) 3 4 5 6 7.5
To Previous Page
Loading...
Need help?
General
