Leaflet No: 0424101 Made in Morocco
Please remember..
it is important to increase the flow rate of your
teat as your baby grows.
Ultra teats are available in the following flow rates:
3
Before first use, clean the product.
3
Clean before each use.
3
Always wash the product immediately after use.
3
Before first use place in boiling water for 5
minutes. This is to ensure hygiene.
3
Wash in warm soapy water and rinse in clean water
or use a dish washer (top shelf only).
3
For cleaning other bottle parts, use a closer to
nature teat & spout brush.
3
Once you have cleaned your bottles they are ready
to sterilise.
3
All bottle components should be sterilised.
3
All bottle components are suitable for sterilisation
by steam (electric or microwave), boiling or cold
water tablet / liquid solution.
3
TAKE EXTRA CARE when cleaning the valve.
In order to ensure optimum venting the teat valve
is manufactured using a thinner silicone than the
teat itself and therefore care needs to be taken
during cleaning to ensure no damage is caused.
7
Do not allow product to come into contact with
oil based foods (e.g. oil / tomato based sauces)
as staining will occur.
7
Do not clean with solvents or harsh chemicals.
7
Do not turn the teat inside out for cleaning.
Damage could result.
7
DO NOT USE A TEAT BRUSH or any other
implement to clean the valve / the feeding hole as
damage such as splits and tears may occur.
However, performance of the teat may be affected
if the valve is not cleaned thoroughly after each
use. Ensure valve is flushed with warm water during
cleaning.
Cleaning and Sterilising
3
Inspect before each use and pull the feeding teat
in all directions. Throw away at the first signs of
damage or weakness.
3
Keep all components not in use out of reach of
children.
3
For safety and hygiene reasons it is recommended
that the feeding teat is replaced every 2 months.
3
When making up a feed, follow the formula milk
manufacturer’s instructions.
7
Do not store or leave in direct sunlight or near a
source of heat or leave in disinfectant (“Sterilising
Solution”) for longer than recommended, as this
may weaken the teat.
7
Do not store with or allow to come into contact
with solvents or harsh chemicals.
7
Not suitable for use in a conventional oven or a
combination microwave oven with
the grill feature switched on.
7
Do not heat in a microwave with bottle sealed.
Remove teat, locking ring and dome cap.
Storage and Use
FOR YOUR CHILDS SAFETY & HEALTH
WARNING!
3
Always use this product with adult supervision.
Accidents have occurred when babies have
been left alone with drinking equipment due to
the baby falling or if the product has been
disassembled.
3
Always check food temperatures before feeding.
Heating in a microwave oven may produce
localised high temperatures. Take extra care when
microwave heating.
3
Always stir heated food to ensure even heat
distribution and test the temperature before
serving.
7
Never use feeding teats as a soother.
7
Continuous and prolonged sucking of fluids will
cause tooth decay. Tooth decay in young children
can occur even when non-sweetened fluids are
used. This can occur if the baby is allowed to use
the bottle for long periods through the day and
particularly through the night, when saliva flow is
reduced or if it is used as a soother.
Warnings
Quick Start
Before use, wash all parts in warm soapy water,
rinse in clean water and sterilise.
Assemble your bottle as per the diagram.
When assembling your bottle
it is important that you check
the valve by holding it to the
light to check that the slit in
the silicone has not sealed
closed. If it has sealed closed,
pinch it gently between your
fingers to re-open. If the valve has sealed
closed your bottle will not vent properly.
Make up your feed.
Serve.
After use, wash all
parts in warm soapy water,
rinse in clean water, ready to sterilise once more.
1
2
3
4
5
6
Any questions?
Visit our website www.tommeetippee.com
call us FREE on 0500 97 98 99 (UK only)
AUSTRALIA: 1800 096 938
NEW ZEALAND: 0800 726 439
0m
+
3m
+
6m
+
slow flow med flow fast flow
1 2 3
BACK
To Previous Page
Loading...
Need help?
General
