Toolots GSN-Z8-1 - User Manual

Questions and Answers

M
Matthew AllenAug 5, 2025
What to do if my Toolots Ice Maker is not running?
- P
  Pamela MillerAug 6, 2025
  If your Toolots Ice Maker isn't running, there could be several reasons. First, ensure it's not in the closed position by pressing the "open key". Check that the ice maker is properly plugged into a functioning socket. Also, inspect the fuse for any damage and replace it if necessary. If ice blocks the evaporator swing blade, remove the ice. For other issues, such as low voltage, blocked air intake, or internal leakage, it's best to contact after-sales service personnel or the power supply department.
H
hopkinsjoshuaAug 15, 2025
Why is my Toolots GSN-Z8-1 producing ice slowly?
- S
  Scott YoungAug 16, 2025
  If your Toolots Ice Maker is producing ice slowly, several factors could be responsible. Check the water pressure and increase it if it's too low. Reduce the water temperature if it's too high. Make sure the ambient temperature is suitable. Clean the condenser if there's too much ash accumulation. Clean or replace the filter screen if it's blocked. Ensure there is at least 15cm space left and rear for proper intake air. For refrigerant leakage, contact after-sales service personnel.
M
Mark MartinAug 26, 2025
How to fix a Toolots GSN-Z8-1 that is not running?
- R
  rsmithAug 26, 2025
  If your Toolots Ice Maker isn't running, start by checking if it's in the closed position and press the 'open key'. Ensure it's plugged into a working socket and inspect the fuse, replacing it if damaged. Clear any ice blocking the evaporator swing blade. If none of these resolve the issue, it may be a proximity switch fault, which requires replacing the proximity switch. For issues like broken connecting lines, insensitive water level detection, or water leakage due to rupture, contact after-sales service personnel. If the air intake is blocked, ensure at least 15cm distance between left and right sides. If the inlet valve has internal leakage, replace it. Make sure all parts are tightened and correctly installed.

Summary

Reception and Inspection

Important Safety Tips

Preliminary Understanding of Your Ice Maker

Box Shell

The main outer casing of the ice maker. No other items should be placed on it.

Evaporator

The component responsible for freezing water into ice.

Water Pipe

The pipe for water supply, ensuring it has no deformation or breakage.

Base Foot

Adjustable feet for leveling the ice maker on uneven surfaces.

Door

The access door to the ice storage or internal components.

Light

Internal light with a bactericidal effect for visibility.

Installation and Placement of Feet

Secure Foot Installation

Screw and tighten feet to the baseplate to prevent bending.

Stable and Level Placement

Place the ice maker on a sturdy, flat surface and adjust feet for leveling.

Installation Environment

Avoid areas with water seepage or high temperatures; ensure ventilation.

Heat Dissipation Clearance

Maintain 30cm clearance for air-cooled models for effective heat dissipation.

Ventilation Maintenance

Do not block the front vents to ensure proper air circulation.

Installation of Water Supply and Drainage

Connect Water Intake Pipe

Connect the external intake pipe to the G3/4 head at the rear cover plate.

Connect to Tap

Connect the other end of the water inlet pipe to the main water tap.

Connect Drain Pipe

Connect the drain pipe to the room outlet with adequate height for drainage.

Cleaning and Maintenance

Peripheral Cleaning

Wipe the exterior weekly with a soft, damp cloth and neutral cleaner.

Ice Spoon Cleaning

Clean the ice spoon with neutral detergent, rinse with clean water, and dry.

Refrigerator Interior Cleaning

Clean the inner wall with neutral detergent and rinse after removing ice.

Pump Cleaning

Disassemble and clean the pump and fan blade with a brush.

Conventional Precautions

Transportation and Placement Tilt

Limit ice maker tilt to 45 degrees during transportation and relocation.

Water Source and Pressure

Use an independent water source; check for low pressure or filter clogging.

Ice Storage Room Hygiene

Keep storage room clear of items and food; ensure ice shovel is clean.

Ice Storage Door Operation

Open and close the ice storage door gently; close sliding door after use.

Environmental Precautions

Keep away from heat sources and avoid extreme temperature environments.

Washing Prohibition

Avoid washing the machine surface directly with water to prevent faults.

Extended Shutdown Procedure

Electrify machine for 4-6 hours every two months if not in use.

Electrical Safety Matters

Grounding Requirement

Ensure a reliably grounded 115V/60Hz power supply or socket is used.

Electric Box Replacement

Professional replacement is required for the 3.8A rated electric box.

Power Supply;Plug Replacement

Professional after-sales service is required for power supply or plug replacement.

Control Panel Operating Manual

Operation Steps of Ice Maker

Power ON;OFF Operation

Use the ON/OFF button to start/stop ice making and enter standby mode.

Timer Setting

Set automatic shutdown timer using the Timing button; adjustable in hours.

Adjusting Ice Making Time and Thickness

Adjust ice making time and ice thickness using Turn Up/Turn Down buttons.

De-icing Procedure

Machine heats to melt ice and restart the ice-making cycle.

Clean Cycle

Use the Clean button to initiate deicing or cleaning cycles.

Display Panel Information

Display shows ambient temperature and ice-making countdown time.

Ice Full Indicator

Machine indicates 'ice full' when ice bin is full and baffle is pressed.

Troubleshooting

Ice Maker Not Running

Troubleshooting steps for when the ice maker fails to start or operate.

Compressor Issues

Diagnosing problems with the compressor not working or stopping suddenly.

Water Intake Problems

Resolving issues related to continuous water intake or overflow.

Water Leakage

Identifying and fixing sources of water leakage from the machine.

Long Ice Making Time

Addressing issues causing prolonged ice production cycles.

No Ice or Thin Ice Production

Troubleshooting to resolve lack of ice production or thin ice formation.

Technical Parameters

Model Identification

The specific model designation for the ice maker.

Rated Voltage

The operational voltage requirement for the ice maker.

Rated Frequency

The operational frequency requirement for the ice maker.

Refrigerant Specification

Type and quantity of refrigerant used in the ice maker.

Rated Current

The electrical current rating of the ice maker.

Vesicant Type

Information about the vesicant or blowing agent used in insulation.

Net Weight

The physical weight of the ice maker.

Product Dimensions

The physical dimensions of the ice maker in inches.

Toolots GSN-Z8-1 Specifications

General

Brand	Toolots
Model	GSN-Z8-1
Category	Ice Maker
Language	English