TOSCA 255-K821-T - User Manual

COMMERCIAL STYLE
WALL-MOUNT KITCHEN FAUCET
255-K821-T – Chrome nish
255-K821-SS-T – Stainless steel nish
255-K821-MB-T – Matte black nish
05/2022
PACKAGE AND HARDWARE CONTENTS
PART DESCRIPTION QUANTITY
A Spout 1
B Faucet body 1
C Spray head 1
D Swivel union 2
E Flange 2
F Rubber washer 2
PREPARATION
SAFETY INFORMATION
Before beginning assembly of product, make sure all parts are present.
Compare parts with the package and hardware contents list. If any part is
missing or damaged, do not attempt to assemble the product.
Contact customer service for replacement parts.
Estimated Assembly Time: 30 minutes
Tools Required for Assembly (not included): Adjustable Wrench, Slip Joint
Pliers, Pipe Wrench, Phillips Screwdriver, and Thread Seal Tape.
Installation may vary depending on how the previous faucet was
installed. Supplies necessary for the installation of the faucet are not
all included; however, they are available wherever plumbing supplies
are sold.
Prior to beginning installation, turn off the hot and cold water lines, then
turn on the old faucet to release built-up pressure. When installing the
new faucet, hand tighten the connector nuts. DO NOT OVERTIGHTEN.
Connections that are too tight will reduce the integrity of the system.
Please read and understand this entire manual before attempting to
assemble, operate or install the product.
WARNING
• Protect your eyes with safety glasses when cutting or soldering water
supply lines.
CAUTION
• If you solder the joints during installation of the faucet, the seats,
cartridges, and washers must be removed before using a ame
or the warranty will be voided on these parts.
• Cover the sink drain to avoid losing parts.
A
B
C
E
D
F
Homewerks Worldwide, LLC • Lake Bluff, IL 60044 • Homewerks.com
Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-877-319-3757,
7:30 a.m. - 4:30 p.m., CST, Monday - Friday.
Due to constant design and quality improvements, the product
may look slightly different from the picture.

Summary

Package and Hardware Contents

Safety Information

Warning

Protect eyes with safety glasses when cutting or soldering water supply lines.

Caution

If soldering joints, remove seats, cartridges, and washers before using flame; warranty void.

Preparation

Product Specifications

Installation Instructions

Shut off water supply and remove existing faucet

Shut off water supply, disconnect lines, remove old faucet, clean and dry surface.

Insert spout into faucet body

Insert spout (A) with o-ring (2.1) into faucet body (B); hand tighten spout nut (2.2).

Wrap thread seal tape and tighten swivel unions

Wrap thread seal tape on pipe threads; screw flanges (E) onto swivel unions (D); tighten unions (D) to pipe.

Insert rubber washer and tighten union nuts

Insert rubber washer (F) into union nut (4.1); tighten union nuts (4.1) to swivel unions (D).

Flush lines and attach spray head

Remove spray head (C) to flush lines; turn on water for one minute; check for leaks; reattach spray head.

Operating Instructions

Care and Cleaning

Troubleshooting

Faucet leaks underneath handle

Leaks under handle due to loose bonnet or dirty cartridge seal. Tighten bonnet or reseat seal.

Water does not completely shut off

Water not shutting off due to worn or dirty ceramic cartridge discs. Remove and clean/replace cartridge.

Faucet leaks around the spray head

Leaks around spray head due to incorrect fitting or dirty rubber gasket. Reseat or replace gasket.

Faucet has an improper water pattern

Improper water pattern due to incorrect spray head fitting or dirty rubber gasket. Reseat or replace gasket.

Faucet leaks at the wall

Leaks at the wall due to loose connection between union nut and swivel union. Gently tighten connection.

Rough-In

Replacement Parts

Limited Lifetime Warranty

TOSCA 255-K821-T Specifications