Introduction
I
Getting
Started
Service
1) Never repair, modify
or
disassemble
the
TV
by
yourself.
It
may cause a fire
or
an electric shock.
Consult a service technician for inspection and
repairs.
2) When a malfunction occurs,
or
if
smoke
or
an unusual odor comes from
the
TV, turn
off
the
TV
and remove
the
power plug from
the
outlet immediately.
Make sure
that
the smoke
or
smell
has
stopped,
then contact a service technician.
If
the
TV
is
still
used in this condition,
it
may cause a fire
or
an
electric shock.
3)
If
the
TV
is
dropped or
the
cabinet
is
broken,
turn off
the
TV
and remove
the
power plug
from
the
outlet immediately.
If
the
TV
has
power in this condition,
it
may cause
a fire
or
an electric shock.
If
the
cabinet
is
broken,
be careful when handling
the
TV
to
prevent an
injury.
Contact a service technician for inspection and
repair.
4) When
the
TV
reaches
the
end
of
its useful life,
ask a qualified service technician
to
properly
dispose
of
the
TV.
Cleaning
CAUTION: Avoid using chemicals (such
as
air
refreshers, cleaning agents, etc.) on or near
the
TV
pedestal. Studies indicate
that
plastics
may
weaken and crack over
time
from
the
combination effects
of
chemical agents and
mechanical stress (such
as
weight
ofTV).
Failure
to
follow these instructions could result in
serious injury and/or permanent damage
to
TV
and
TV
pedestal.
1) Remove
the
power plug before cleaning.
Never use solvents such
as
benzine
or
thinner
to
clean
the
TV.
These solvents may
distort
the
cabinet
or
damage its finish.
If
rubber
or
vinyl products remain in contact
with
the
TV for a long time, a stain may result.
If
the
cabinet becomes dirty, clean
it
with
a soft,
dry
cloth.
When cleaning
the
surface
of
the
LCD
display,
wipe
the
panel surface
gently
with
a soft,
dry
cloth.
2) Periodically disconnect
the
power plug from
the
outlet and check it.
6
If
dust has collected on
the
power plug
connectors, clean
off
the
dust with a
dry
cloth.
This dust may cause a fire due
to
reduced
insulation on
the
plug.
Im
ortant
Information
1) About
LCD
screen
If
you have
the
LCD
screen facing
to
the
sun,
the
LCD
screen will be damaged.
Be
aware
of
locating
the
TV close
to
a
window
or
outdoors.
Never press
the
LCD
screen strongly
or
scratch
it, and never
put
anything on it. These actions
will damage
the
LCD
screen.
2) About cabinet and
LCD
screen
Never spray volatile compounds such
as
insecticide on
the
cabinet and
LCD
screen.
This may cause a discoloration
or
damage
the
cabinet and
LCD
screen.
3) About afterimage
If
a still picture
is
displayed, an afterimage may
remain on
the
screen, however
it
will disappear.
This
is
not
a sign
of
malfunction.
4) Some pixels
of
the
screen
do
not
light
up
The
LCD
display panel
is
manufactured using an
extremely high level
of
precision technology,
however sometimes some pixels
of
the
screen
may be missing picture elements
or
have
luminous spots. This
is
not
sign
of
malfunction.
5) About Interference
The
LCD
display may cause interference in image,
sound, etc.
of
other
electronic
equipment
that
receives electromagnetic waves (e.g. AM radios
and video equipment).
6) About using under
the
low
temperature places
If
you
use
the
TV in
the
room
of
0°C
or
less,
the
picture brightness may vary until
the
LCD
monitor
warms up. This
is
not
a sign
of
malfunction.
7) When disposing
of
or
transferring ownership
of
the
TV
Before disposing
of
or
transferring ownership
of
the
TV,
perform "Resetting the
TV".
Recommended
Picture
Mode
There
are
five choices(User, Cinema, Sport,
Vivid and Hi-Bright)
in
picture mode setting.
The
default one
is
Vivid, which
is
recommended
for home viewing. If you wanna restore the
picture mode
to
Vivid, you
can
operate the setting
of
"Reset Default"
in
Setup menu. And also you
can
set the desired picture mode directly in
Picture menu.
Please
refer
to
the following.
1
).
Press
MENU and
OK
buttons
to
enter the
main menu.
2).
Press
Ji.IT and
OK
buttons
to
select "Video"
or"Setup" menu.
3).
Press
Ji.IT and
OK
buttons
to
select "Picture
Mode" or "Reset Default".
4).
Press
Ji.IT button to select the recommended
ode "Vivid"
in
"Picture Mode",or
press
OK
button
to
restore
all
the user settings
to
the
default value in "Reset Default".
Note:
All
the
user
settings
will
lose
completely
after operating the
feature
of"Reset Default".
To Next Page
Loading...
