Need help?Do you have a question about the Toshiba Aplio SSA-770A and is the answer not in the manual?
General| Type | Ultrasound System |
|---|---|
| Manufacturer | Toshiba |
| Display | 19-inch LCD |
| Probe Connectors | 4 |
| Model | SSA-770A |
| Imaging Modes | Color Doppler |
| Power Supply | AC 100-240 V, 50/60 Hz |
| Operating Humidity | 30 to 80% (non-condensing) |
| Storage Humidity | 10 to 90% (non-condensing) |
Identifies the service manual and its number.
Details manual revisions, dates, reasons, and authors.
Defines signal words and explains safety symbols used in the manual.
Covers explosion hazards, equipotential connection, circuit protection, and RF interference.
Overview of the five main systems comprising the diagnostic ultrasound system.
Lists PWB names, drawing numbers, and remarks for each unit.
Shows the signal flow and components of the front-end unit.
Identifies major sections of the system for SSA-770A/700A (CRT/LCD).
Step-by-step guide for removing SSA-770A covers (side, front).
Instructions for removing the handle from the SSA-770A.
Instructions for removing the handle from the SSA-700A.
Detailed steps for removing the monitor unit with a CRT display.
Detailed steps for removing the monitor unit with an LCD display.
Step-by-step guide for detaching the LCD monitor arm assembly.
Procedure for adjusting the vertical movement resistance of the LCD monitor arm.
Steps for removing the operating panel and its associated covers for SSA-770A.
Steps for removing the operating panel and covers for SSA-700A.
Procedure to remove the lower cover of the operating panel assembly.
Steps to detach the upper panel from the operating panel assembly.
Instructions for detaching the handle from the operating panel.
Procedure to disconnect and remove the trackball component.
Steps for removing printed wiring boards B and G from the assembly.
Steps to detach the keyboard and its connector from the panel.
Procedure for detaching the LCD assembly and associated brackets.
Steps for removing printed wiring boards C, D, and E from the assembly.
Procedure to remove the near/away slide lever mechanism.
Procedure to remove the up/down slide lever mechanism.
Steps to detach the PWB rack and its retainer from the system.
Procedure for removing the Transducer Interface board.
Procedure for removing the Input/Output unit.
Detailed procedure for removing the Hard Disk Drive unit.
Steps for disconnecting and removing the system battery.
Procedure for detaching the AC-DC power supply unit.
Steps for removing the Power Supply Analog and Digital units.
Procedure for detaching the transformer tray from the system.
Steps for disconnecting and removing the Magneto-Optical drive.
Detailed steps for removing the front panel of the SSA-770A.
Detailed steps for removing the front panel of the SSA-700A.
Steps for detaching the rear panel and its covers from the system.
Procedure for removing the PHYSIO unit and associated covers for SSA-770A.
Procedure for removing the PHYSIO unit and associated covers for SSA-700A.
Steps to remove caster units and covers from the SSA-770A system.
Steps to remove caster units from the SSA-700A system.
Instructions for removing and cleaning system air filters.
Procedures for cleaning key tops and other panel components.
Procedure for adjusting the up/down slide wire mechanism.
Procedure for adjusting the near/away slide wire mechanism.
Steps for replacing the up/down slide wire assembly.
Procedure for replacing the near/away slide wire assembly.
Steps for removing and securing the CD-R drive unit.
Instructions for cleaning the lens actuator of the MO drive.
Procedure for cleaning the older model of the palm switch.
Procedure for cleaning the newer model of the palm switch.
Introduction to the Front-End Unit and its constituent boards.
Overview and functional description of the Transducer Interface board.
Details error detection mechanisms and transmission disable signals on the TI board.
Overview and functional description of the Transmit/Receive board.
Overview and functional description of the Receive Control board.
Details error detection mechanisms within the Receive Control board.
Overview and functional description of the Continuous Beamformer board.
Overview of the BE Unit and its constituent boards.
Details functions of DR, EP, FP, SIP, SC, and PCI I/F blocks.
Overview and functional description of the Video Interface board.
Overview and composition of the Realtime Manager board.
Introduction to the IQ Data Acquisition board and its circuit functions.
Overview and functions of the I/O board for system connectivity.
Description of the front panel's outline and its functions.
Description of the rear panel's outline and its functions.
Overview of the operating panel and its communication methods.
Lists the four main units comprising the system's power supply.
Schematic showing the functional blocks of the power supply unit.
Details specifications for line voltage input and power consumption.
Lists output voltages and current ratings for various power supply units.
Describes the primary functions of the transformer tray unit.
Lists the functions performed by the AC/DC tray unit.
Overview and specifications for the PSA and PSD power supply modules.
Table explaining the meaning of each LED status for error indication.
Technical specs and adjustment procedures for the CRT monitor.
Technical specs and adjustment menu guide for the LCD monitor.
Introduction to the PHYSIO Module, its signals, and functions.
Visual representation of unit interconnections within the system.
Details the directory structure for system and application software.
Describes error logging, message structure, and severity levels.
Outlines presets (System, Exam, App, Imaging) and their editors.
Explanation of the System Preset and its parameter configuration.
How Exam Type sets transducer, imaging, and application presets.
Details parameters in Application Presets for user customization.
How to select and confirm Exam Type on the patient information screen.
Guides for using the System, Exam Type, and Application Preset editors.
Details parameters for system, peripheral, output, and exam information settings.
Covers settings for transducers, external devices, reports, and work orders.
Includes 2D mode, ACT, Appl Meas, Window, D-Mode, OB, Carotid settings.
Procedure for changing the PC name for network compatibility.
Standard steps for upgrading the system software.
Shows default layout and how to change panel configuration files.
Details switch function changes for layouts and label application.
Procedures for adjusting system time or both date and time.
Introduction to the 3D position sensor, its components, and functions.
Purpose, cases, and steps for performing the magnetic field distortion check.
To Next Page
