Reference Information
Toshiba 2-11
29
RECORDING
MTS Broadcast Compatibility ( For W-522 only )
This VCR can receive or record MTS (Multichannel TV Sound) broadcasts. By connecting the VCR to
your stereo system or stereo TV, you will experience the SAP or stereo sound.
Preparation
Connect a stereo TV or stereo system to the AUDIO OUT jacks of the VCR.
Recording the SAP/Stereo Broadcast
1
On the SET UP screen (page 15),
select “SAP SET” using
PLAY
or
STOP
, and set to “ON” using
REW
or
FF
.
2
Press
PROG
. once to exit.
3
Perform a recording.
SAP (Second Audio Program broadcast):
A separate audio program, usually broadcast in a second language with the
main language.
Selecting a sound
Sounds recorded on the tape
According to your setting of “SAP SET” on the SET UP screen, the sound is recorded onto different
tracks of the tape as below. Set “SAP SET” to “ON” or “OFF” appropriately.
Hi-Fi sound track
Contents of recorded sound
On-Screen Display
(Press
DISPLAY
.)
Setting of “SAP SET”
on the SET UP
screen
Type of receiving
broadcast
Normal sound
track (Mono)
L
R“SAP”“STEREO”
“ON” or “OFF” not lit not lit MONO MONO MONO
“ON” or “OFF” not lit lit MONO (MIXED)
“ON” lit not lit MONO MONO SAP
“OFF” lit not lit MONO MONO MONO
“ON” lit lit MONO MONO SAP
“OFF” lit lit MONO (MIXED)
STEREO
STEREO
Regular
(monaural audio)
Stereo
Regular+SAP
Stereo+SAP
Sounds in playback
You can play SAP and/or stereo broadcasts with this VCR. Press
A.SELECT
to select a desired sound.
Note
When the TV is connected to the RF OUT terminal of the VCR, the output sound is monaural.
Desired sound
SAP sound
Stereo sound
L , R indicators in the On-Screen display
R (right) is on.
Both R (right) and L (left) are on.
Sound output
SAP
HIFI Sound
RECORDING
SLOW
PAUSE/STILL
REC TIMER
TV
VCR
POWER
I.SELECT
SP/SLP
DISPLAY
TV VOL
COUNTER
PROG.
CANCEL
REMAIN/
RESET
COUNT
EJECT
CM SKIP
1
2
3
6
5
4
100
9
87
0
ENTER
A.SELECT
STOP
FF
REW
PLAY
1
A.SELEC
T
28
Confirming the timer programs
Press
PROG.
during timer recording mode.
The screen for confirming will appear.
Press
PROG
.again to exit from confirmation
page.
Changing/cancelling the timer
programs
1) If the
TIMER
indicator is lit, press both
TIMER
to turn it off, and then turn the VCR
on by pressing VCR
POWER
.
2) With steps 2 to 9, change the items.
To cancel a program, select the program you
want to cancel in step 4, and press
CANCEL.
The line is then cleared.
3) Press both
TIMER
to return to the timer
standby mode.
Error indication
The “--E-” ( Error ) indicator appears in the VCR
display if you press both
TIMER
when:
–– a cassette is not loaded.
–– the loaded cassette has no safety tab.
–– timer recording is in progress.
In these cases, a recording can not be made.
To cancel the Timer Recording
By pressing the
POWER
button on the front
panel of the VCR, it will cancel the timer
recording and go to standby.
P
M
P
M
Program 1
(Start time)
Overlapped portion
(not recorded)
Program 2
(Start time)
Overlaps of the programs
If two timer programs overlap, the recording
start time of program 1 has priority over the
recording off time of program2.
If a power failure occurs during
the timer program recording
• When a power failure has occurred, the
programmed contents are not affected,
reset the clock.
To Next Page
Loading...
