Total TGTLI20301 - User Manual

Need help?

Do you have a question about the Total TGTLI20301 and is the answer not in the manual?

Overview

Function Description
Important Technical Specifications
Usage Features
Maintenance Features

The TOTAL TGTLI20301 is a 20V battery-powered grass trimmer designed for garden maintenance. It is part of the TOTAL One-Stop Tools Station, indicating compatibility with the P20S battery system.

Function Description:

The device is primarily used for trimming grass and edging lawns. It features a cutting head that uses a nylon line to cut vegetation. The trimmer is designed for ease of use and maneuverability, with an extendable bar and an adjustable front handle to suit different user heights and working angles. A protective clip (flower protector) is included to shield garden plants from accidental cutting. The tool can be switched between trimming and edging modes by rotating the cutting head 90 degrees.

Important Technical Specifications:

Voltage: 20V
No-load speed: 8200 rpm
Cutting diameter: 300 mm
Sound power level (measured according to ISO22868): 92.8 dB (A) K=3
Sound pressure level (measured according to EN60335-1 + EN50636-2-91): 76.1 dB (A) K=3
Guaranteed sound power level: 94 dB (A)
Vibration levels in the handles (front/rear) (measured according to ISO22867): 1.28 / 1.02 m/s² K=1.5
Recommended nylon diameter for coil replacement: 0.065 inches (1.6 mm)

Usage Features:

Battery System: Operates on a 20V battery, which is part of the P20S tool system. Users should only use batteries and chargers specified by the manufacturer.
Start/Stop Mechanism: The trimmer is started by pressing a lock button and then pulling the trigger switch. Releasing the trigger stops the mower.
Extendable Bar (2): The length of the mower can be adjusted to various extension points for comfortable use, accommodating different user heights.
Adjustable Front Handlebar (3): The front handle can be adjusted in angle (from 30° to 180° in 3 steps of 30°) to provide better control and ease of use during operation.
Cutter/Edge Trimmer Switch Button (1): This button allows the user to rotate the cutting head 90 degrees, converting the tool from a trimmer to an edge bander.
Protective Clip (9): An easy-to-mount accessory that protects garden plants and the nylon line from damage during cutting.
Cutting Feed: The machine features an automatic feeding head. To advance the line, the user releases and then pulls the switch trigger twice. Each double pull extends the line approximately 1/4 inch.
Manual Cutting Feed: The nylon line can also be advanced manually by pulling the tool's coil retention button.
Knife Cut: The brush cutter is equipped with a cutting blade on the grass guard, which helps maintain the correct nylon length.
Edging: For edging, the battery is removed, the shift button (1) is pressed, and the machine head is rotated 180° clockwise.
Work Area Safety: Users are advised to keep the work area clean and well-lit, avoid explosive atmospheres, and keep children and unauthorized persons away.
Personal Safety: Always be careful, observe surroundings, and use common sense. Do not operate when tired or under the influence of substances. Wear appropriate personal protective equipment (PPE) including eye protection, ear protection, and sturdy shoes.
Electrical Safety: Ensure battery charging plugs match the socket. Use only specified batteries and chargers. Avoid body contact with grounded surfaces. Do not expose tools to rain or moisture. Stop the engine immediately if problems occur.
Vibration Emission: The actual vibration emission value may differ based on tool usage, condition, accessory, and grip force. Improper handling can cause hand-arm vibration syndrome.
Noise Emission: The device has a guaranteed sound power level of 94 dB (A). Hearing protection is recommended.

Maintenance Features:

General Maintenance: Before inspection, cleaning, or repair, stop the engine and remove the battery. Always wear safety glasses or side shields.
Coil Replacement (Fig. 13):
- Push the tabs on the side of the spool retainer.
- Remove the bobbin stopper and the coil.
- Install the new spool, ensuring the nylon is held in the grooves.
- Thread the nylon through the eyelets.
- Move the nylon so it extends from the tip.
- Reinstall the spool retainer by pressing the tabs into the slots until it snaps into place.
Nylon Replacement (Fig. 13-14):
- Remove the battery and the spool from the nylon head.
- Use only 0.065" (1.6 mm) diameter monofilament nylon.
- Insert the new nylon thread into the hole in the bobbin, then wind the thread around the bobbin in the direction indicated by the arrows.
- Ensure there are at least 6 inches between the wrapped nylon and the outer edge of the spool.
- Thread the grass through the eyelets so it comes out of the housing.
Charger Maintenance:
- Keep the magazine clean and free of debris.
- Prevent foreign material from entering the cavity or contacts.
- Clean the charger with a dry cloth. Do not use solvents or water.
- Do not place the charger in humid environments.
- Unplug the charger when the battery is low.
- Fully charge batteries before storing them.
- Store the charger at normal room temperature, away from excessive heat or direct sunlight.
Cleaning:
- Avoid using solvents that can damage plastic parts.
- Use clean clothes to remove dirt, dust, oil, and grease.
- Avoid brake fluids, gasoline, petroleum-based products, and penetrating oils, as they can damage plastic parts.
- Periodically clean all foreign material from the trimmer head vents.
Storage:
- Open the attachment of the telescopic arm and put it in the shortest position.
- Clean all foreign material from the trimmer.
- Keep it in a place inaccessible to children.
- Stay away from corrosive agents such as garden chemicals and antifreeze salts.
- Store the equipment in a lockable area.
- Keep hands and feet away from the cutting area, especially when starting the engine.
- Never use the machine if you are tired, if you are not 100% trained, or if you are taking any medications that could affect your vision, judgment or coordination.
- Turn off the machine when you need to transport it. Always remove the battery when finishing work, storing the machine or passing it to someone else.
Troubleshooting: The manual provides a table for common issues like LED indicator status during charging, nylon not feeding, nylon wraps, and engine not starting, along with possible causes and solutions.
Environmental Protection: Waste electrical products must not be disposed of with household waste. Recycle at appropriate facilities. This product should be disposed of in an appropriate recycling facility. Plastic components are labeled for classified recycling.