Track Tester
• Quickly tests track for power faults
• Low cost and easy to use
• Works on N, TT, OO or HO Track
• Indicates the DC polarity, or DCC, or a fault
• Small enough to check point frogs
DCC Fitted
Digital Signals
• Signal with DCC decoder built into base
• Can just plug direct into track – no wires!
• Easy to fi t and use – no CV programming!
• Can sync to other signals & points
• Available with Feathers & Theatres
One-Touch DCC
™
Point Controllers
DCC
N Z
• Control points and uncouplers using DCC
• Work with most solenoid point motors
• Just connect 2 wires to DCC rails - No CV Programming!
• Easy screw terminals – no soldering
• Built in CDU for effi cient operation
• Can sync to other points and signals
One-Touch DCC
™
Signal Controllers
• Control LED & Semaphore signals by DCC • Easy screw terminals – no soldering
• Easy to set up & use –No CV programming! • Can sync to other points & signals
DCC
ANY
GAUGE
Buffer Lights
• Add realistic stop light to any siding
• Simply clips onto track – No wires!
• Fits next to most buffer stops & kits
• Or at platform end or free standing
• On DCC both lights are on constantly
• On DC one light is on & varies with speed
N
Track and buffer stop not included
HO
OO
N
N
Automatic Tail, Firebox & Loco Lights
• No switch - senses motion & turns on!
• Turns off automatically 4 minutes after stop
• No pickup, wires or soldering - LED plugs in
• Fit in brake vans, coaches, loco, wagons etc
• Runs for ages on small button battery
• LEDs and batteriy included
LFX
Lighting Effect Controllers
• Easily add lighting effects to your layout
• LEDs screw in – no resistors or soldering
• Powered by 9v battery, 9-16V DC or DCC
• On DC the effect is on when powered
• On DCC the effect can be controlled
• Effects LEDs are included
ANY
GAUGE
ANY
GAUGE
Signal Kits
Auto
SEE WWW.TRAIN-TECH.COM OR CONTACT DCP FOR FREE COLOUR BROCHURE
WIRE
FREE
WIRE
FREE
Rolling stock not included
Fits in N
scale upwards
1017
DC &
DCC
HO
OO
N
Automatic Coach Lighting
• Easy to fi t in seconds - no wiring!
• No switch - senses motion & turns on!
• Turns off automatically 4 minutes after stopping
• No pickups so works on regular DC & DCC
• Traditional warm white or modern cool white
• Also with tail light, sparks or door light effect
• Lights stay bright & constant with no fl ickering
• Fits most OO/HO coaches and maybe cut down
OO
HO
Auto
WIRE
FREE
Rolling stock not included
DC &
DCC
Track not included
Only
£5
DC &
DCC
DC &
DCC
DC &
DCC
DC &
DCC
OO
HO
OO
HO
OO
HO
OO
HO
OO
HO
WIRE
FREE
DCC
HO
OO
N
SFX Sounds for Trains
• Easy low cost sound that works on
any
railway
• Easy to fi t in seconds - no connections
• No switch - senses motion & turns on!
• No pickups so works on regular DC & DCC
• Self contained - built in speaker & battery (included)
• Tiny capsule: 25mm x 20mm x 12mm approx
• Fit capsule into loco, tender, wagon, coach...
• Real recorded sounds - Steam & Diesel etc
Auto
DC &
DCC
WIRE
FREE
Only
£5
Automatic Sensor Signals
• Detects train and changes signal automatically
• Use on its own & signal changes back to green after time
• Or link to other SS for automatic block signalling
• Can be used on both DC & DCC
• Also available with Feathers & Theatres
OO
HO
WIRE
FREE
DC &
DCC
Mimic Switches & Lights
• Make a mimic panel to control LayoutLink items
• Link to Track Sensors or Sensor Signals to show
occupancy & signal status
• Single wire to control Layout Link products
• Link to Sensor Signals to switch route indicators on/off
DC &
DCC
ANY
GAUGE
• Low cost – adapt to your own design
• Control by switches or signal controller
• LEDs are prefi tted to a narrow PCB
Every kit includes
the signal head,
aluminium post
and base plus
detailing kit
Smart Lights - Easy to fi t Lighting Effects
• Small - Just 1cm x 1cm x 0.3cm with 2 wire connections
• Power by standard 9-16v DC or a 9v battery
• Or by DCC which can also control some effects
• Just connect and go - no setting up required
• Disco / Emergency / Real Fire / TV / Welding / Random effects
DC &
DCC
ANY
GAUGE
Level Crossing - Ready Assembled
• Power from 9-16v DC, DCC or a 9v battery
• Light and sound - all connections easy push fi t
• Includes 2 x Peco static level crossing barriers
• Can turn on automatically using a Track Sensor
• Available in single and pair packs
N
DC &
DCC
OO
HO
Track Sensor
• Change Semaphore Signals automatically (with SC300)
• Trigger Level crossing when train approaches
• Power from 12-16v smooth DC or DCC
• Links to a Mimic Switch to show occupancy
• Links to a Sensor Signal to change block section
DC &
DCC
OO
HO
Traffi c Lights - Ready Assembled
• Power from 9-16v DC, DCC or 9v battery - 2 Wire connection
• Realistic standard UK sequence and timing varies randomly
• Fully assembled - drill hole in baseboard & connect to power
DC &
DCC
OO
HO
Need help?
General
To Next Page