To set
the heater to the Frost Watch mode, rotate the thermostat control knob fully to the lowest
setting (N, 1) Thereafter the heater will trip in if the temperature drops sufficiently. The heater needs to be in
the “ON” mode with the neon indicator light illuminated for this function to operate.
Product Warranty – 10 year warranty
Any bathroom heater that is found to be defective due to substandard materials and/or workmanship within 10
(ten) years from the
date of purchase, will be replaced. To make a claim under this warranty, contact Tranquillity New Zealand on 0800 805 558. Your
warranty applies only if:
• Your heater is installed, tested and signed off by a registered electrician.
• You provide us with written proof of your
purchase
and your
warranty registration.
If
this
warranty applies:
• Tranquillity New Zealand
will send
out a qualified person to repair/replace the heater on site.
• Repair or replacement of the heater will be at Tranquillity’s discretion.
The benefits given by this warranty are additional to other rights and remedies that you may have under laws relating to our
products. Our goods come with guarantees that cannot be excluded under the New Zealand/Australian Consumer Law. You are
entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage.
You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not
amount to a major failure. If you have any questions about the performance of your heater, which may not be to your satisfaction,
please call Tranquillity New Zealand - Freephone: 0800 805 558.
Tranquillity New Zealand is not responsible for:
• Damage done or repairs required as a consequence of the faulty installation or application of your
heater.
• Damage done a
s a
result of
environmental factors
affecting your
heater which
are beyond Tranquillity’s control.
• Damage done or repairs required as a result of any improper use, maintenance, operation or servicing of your heater.
• Incidental on consequential damage of any kind, including but not limited to costs or expenses resulting from damage to any
property.
The Whisper is fitted with a thermostat - To set the thermostat to
the required temperature,
turn the control knob fully clockwise. When the desired room temperature is
reached, turn
the knob slowly anti-clockwise and when the thermostat ‘clicks’ off, leave the control at this
setting. Thereafter, the
fan heater will control the heat output automatically.
⁻ ⁺
Hot
Cold
NEW ZEALAND PHONE 0800 805 558 EMAIL info@tbw.co.nz www.tbw.co.nz
AUSTRALIA PHONE 1300 62 11 51 EMAIL info@formebathroomcollection.com.au www.formebathroomcollection.com.au
The Whisper has a heat loading of 2kW. The heater is
controlled by a pullcord operated on/off switch. A neon
indicator when lit shows that the unit is operational.
The appliance is fitted with an Electronic Safety Control (ES). This is a safety device which switches off the heater if for
any reason the appliance overheats. The ES control can only be re-set after the appliance has cooled down. In order to
re-set the ES Control proceed as follows:
• Switch off appliance by means of pullcord and leave for approximately 5 mins
• Switch appliance back on
and ES control will re-set
• Ensure that the appliance is functioning correctly. Is the ES Control operates again, the appliance should be
checked by a registered electrician.
• Secure the mounting bracket to the appliance using the three No. 6 screws supplied (Ref B in diagram)
• Position the appliance on the partially inserted wall screws and secure the third wall screw immediately
above the appliance.
Cleaning
Always disconnect the heater from the mains before cleaning. The fan heater should always be kept clean. An
occasional wipe over with a soft cloth is all that should be necessary, ensuring all inlet and outlet vents are kept dust
free.
• Do not use metal or furniture polish on any part of the heater.
• Do not touch the heater with wet hands or in
any way bring water in contact with it.
The supply cord on this appliance can only be replaced by the use of special tools, and should any damage or fault
occur to the heater, it must be serviced by an accredited service agent.
Thermostat Control
Controls
• Using the mounting bracket supplied as a template, position it horizontally at a
minimum of 1.92m from the floor to the underside of the bracket and mark the position
of the three fixing holes (Ref A in diagram)
• Drill and plug the wall suitable of No. 8 screws
• Insert the two keyhole screws in the wall leaving approximately 2mm gap between head
Mounting Procedure
To Previous Page
Loading...