Home
Transition Networks
Network Hardware
ION x6010
Transition Networks ION x6010 - User Manual
299 pages
Manual
Specs
Ask a question
Save Page as PDF
To Next Page
To Next Page
Loading...
Transition Network
s
ION x6010 User Guide
33493 Rev. E
https://www.transiti
on.com/
Page 1 of 299
x6010 Managed T1/E1-to-Fiber
Network Interface Device (NID)
User Guide
33493
Rev. E
2
Table of Contents
Main Page
Default Chapter
5
Table of Contents
5
Section 1: Introduction
10
Document Overview
10
Product Overview
10
Features
10
Typical Application
11
Figure 1: Typical X6010 User Application Scenario
11
Applicable Standards and Rfcs
12
Feature Descriptions
12
AIS (Alarm Indication Signal)
12
Figure 2: Typical AIS Application
12
Loopback Test
13
Figure 3: Loopback on Copper and Fiber Port of Media Converter a
13
LOS (Loss of Signal) Detection
14
In-Band Fiber Loopback Code Detection
14
Figure 4: Typical Loopback Function on a Fiber Port
14
Figure 5: Typical Loopback Function on a Copper Port
14
Http
15
Table 1: HTTP Parameters
15
Remote Management
17
Figure 6: Typical Remote Management Application
17
Figure 7: X6010 Remote Management Topology
18
Firmware Upgrade
19
Management Access Methods
20
TFTP (Trivial File Transfer Protocol)
20
Optional Accessories (Sold Separately)
20
Models (Chassis and Standalone)
21
Figure 8: X6010 Models
21
Table 2: X6010 Models
22
Physical Specifications
23
Table 3: Physical Specifications
23
Connectors
24
Figure 9: C6010 Front Panels
24
Table 4: X6010 Connector Descriptions
24
LED Descriptions
25
Figure 10: S6010 Front Panels
25
Jumper Settings
26
DIP Switches
26
Figure 11: S6010 DIP Switches
26
Figure 12: C6010 DIP Switches
27
Documentation Conventions
29
Table 5: Documentation Conventions
29
Related Manuals and Online Help
30
For more Information
30
Section 2: Installation and System Setup
31
General
31
Installing the Chassis Model (C6010)
31
Figure 13: Chassis Installation
31
Installing the Standalone Model (S6010)
32
Rack Mount Installation
32
Tabletop Installation
33
Figure 14: Tabletop Installation
33
Wall Mount Installation
34
Figure 15: Wall Mount Installation
34
Connecting to AC Power
35
Figure 16: AC Power Connection
35
Installing Sfps
36
Connecting the C6010 to the S6010
36
Figure 17: SFP Installation
36
Accessing the Nids
40
Access Via Local Serial Interface (USB)
40
Access Via an Ethernet Network
41
Initialization (Default) Configuration
45
Section 3: Management Methods
46
General
46
IONMM Managed X6010
46
Managing Slide-In and Remote Modules Using CLI Commands
46
Figure 18: CLI Location Hierarchy
47
Managing Slide-In and Remote Modules Via the Web Interface
50
Managing Standalone Modules Using CLI Commands
51
Managing Standalone Modules Via the IONMM Web Interface
52
Menu Descriptions
54
Table 6: System-Level Menu Description
54
Table 7: Port-Level Menu Description
55
Reboot, Reset, and Power off Function Notes
56
Table 8: Back up and Restore File Content and Location
56
Table 9: File Status after a Reset to Factory Defaults
56
Table 10: File Content and Location after a System Reboot
56
Section 4: Configuration
59
General
59
System Configuration
60
System Configuration - CLI Method
60
T1 System Configuration - Web Method
61
T1 Ports Configuration
62
T1 Ports Configuration - CLI Method
62
T1 Ports Configuration - Web Method
63
Port Loopback Tests
66
Port Loopback Test - CLI Method
66
Port Loopback Test - Web Method
68
TDM Mode Configuration
70
Configuring TDM Mode - CLI Method
70
Configuring TDM Mode - Web Method
71
Section 5: Operation
74
General
74
Backup and Restore Operations (Provisioning)
74
Note on Remote (L2D) Module Backup, Restore, and Upgrade
75
Backing up Slide-In and Remote Module Configuration
75
Backing up Standalone Modules
78
Editing the Config File (Optional)
80
Restoring Slide-In and Remote Modules' Configuration
81
Restoring Standalone Modules
84
Back up and Restore File Content and Location
87
IONMM Backup All / Restore All
87
Displaying Information
88
Reset to Factory Defaults
88
Resetting Defaults - CLI Method
88
Resetting Defaults - Web Method
89
File Status after Reset to Factory Defaults
89
Resetting Uptime
90
Reset Uptime - CLI Method
90
Reset Uptime - Web Method
91
Reboot
92
Rebooting - CLI Method
92
Rebooting - Web Method
93
Reboot File Content and Location
94
Upgrade the IONMM And/Or NID Firmware
95
Upgrading IONMM And/Or NID Firmware - CLI Method
95
Upgrading IONMM And/Or NID Firmware - Web Method
97
Upgrading Slide-In and Remote Modules Firmware Via TFTP
103
Firmware Upgrade File Content and Location
107
Additional Upgrade Procedures
107
Table 11: File Content and Location after a Firmware Upgrade
107
Replacing a Chassis Resident NID
108
Section 6: Command Line Interface (CLI) Reference
109
General
109
Command Line Editing
109
Display Similar Commands
109
Partial Keyword Lookup
109
Recall Commands
109
Keystroke Commands
110
Table 12: Keystroke Editing Commands
110
Command Descriptions
111
Section 7: Troubleshooting
127
General
127
Basic ION System Troubleshooting
127
Error Indications and Recovery Procedures
128
LED Fault and Activity Displays
129
Problem Conditions
130
CLI Messages
141
Web Interface Messages
173
The Config Error Log (Config.err) File
188
Config.err Messages
189
Config.err Message Responses
189
Webpage Messages
192
Windows Event Viewer Messages
202
ION System Tests
203
DMI (Diagnostic Maintenance Interface) Test
203
Table 13: DMI Parameters
205
Set Debug Level
211
DIP Switches and Jumper Settings
212
PCB Identification
212
C6010 Pcb
212
Figure 19: X6010 PCB Layout
212
S6010 NID Switch Locations
213
Figure 20: X6010 Switch Locations
213
X6010-10Xx PCB (C6010 with SFP and BNC)
217
Figure 21: X6010-10Xx Layout
217
In-Band Loopback Code Detect Procedure
218
Figure 22: Initiate a Loopback from a Test Set
218
Third Party Troubleshooting Tools
219
Third Party Tool Messages
231
Hyperterminal Messages
231
Ping Command Messages
234
Telnet Messages
234
TFTP Server Messages
236
Putty Messages
237
Alarm Indication Signal - Alarm Condition
238
LOS Detection
240
T1 Error Events and Alarm Conditions
240
T1 Error Events
240
D4 and ESF Alarm Conditions
240
Recovery Procedures
241
Recording Model Information and System Information
242
Technical Support
244
Contact Us
244
Appendix A: Warranty and Compliance Information
245
Warranty
245
Compliance Information
246
Declaration of Conformity
247
Electrical Safety
248
Elektrische Sicherheit
248
Elektrisk Sikkerhed
248
Elektrische Veiligheid
248
Sécurité Électrique
248
Sähköturvallisuus
248
Sicurezza Elettrica
248
Elektrisk Sikkerhet
248
Segurança Eléctrica
248
Seguridad Eléctrica
248
Appendix B: Factory Defaults
249
Device-Level Factory Defaults
249
Port-Level Factory Defaults
249
Table 14: Device-Level Factory Defaults
249
Table 15: Port-Level Factory Defaults
249
Supported Line Build out Matrix
250
Table 16: Line Build out (LBO) Details
250
Appendix C: Configuration Quick Reference - CLI
251
For SNMP MIB Trap Information
252
Appendix D: Cable Specifications
253
Fiber Specifications
253
Fiber Cable
253
T1/E1 Cable
253
Twisted-Pair Copper Cable
253
T1 Tp/Utp
253
E1 Tp/Utp
253
Appendix E: Local Management of Cards in a Remote Un-Managed Chassis
254
Glossary
263
Index
297
Need help?
Do you have a question about the Transition Networks ION x6010 and is the answer not in the manual?
Ask a question
Transition Networks ION x6010 Specifications
General
Brand
Transition Networks
Model
ION x6010
Category
Network Hardware
Language
English
Need help?
General
To Next Page