Travis Industries Avalon 900 PS

Questions and Answers

K
kathleensnyderAug 17, 2025
Why won't my Travis Industries Avalon 900 PS Pellet stove heater start?
- R
  Robert JohnsonAug 17, 2025
  If your Travis Industries Pellet stove heater won't start, there are several potential causes: * The heater might not be properly plugged in; ensure it is connected to a power source. * The power button might not be turned on, or the start button might not be pressed. Please refer to the "Starting Your Heater" section for guidance. * There might be an interruption in the power supply. Check your household fuse or breaker. * A fuse might have blown. Consult the "Fuse Blown" section for instructions.
J
Jill FlowersAug 20, 2025
What to do if the firepot overfills with pellets in my Travis Industries Avalon 900 PS Pellet stove?
- M
  mmanningAug 20, 2025
  If the firepot in your Travis Industries Pellet stove is overfilling with pellets, it could be due to: * The AIR CONTROL being too far in. Consult the "Operating Your Heater" section for proper adjustment. * A plugged firepot. Refer to the "Check the Firepot" section for cleaning instructions. * An air leak. Consult the "Air Leaks" section to identify and resolve any leaks. * Clogged exhaust ducts. See "Clean the Exhaust Ducts" for instructions on how to clean them. * A clogged exhaust system. Check the "Exhaust Blower" section for details on how to resolve this issue.
J
Julie JohnsonAug 22, 2025
Why are pellets not feeding into my Travis Industries Avalon 900 PS Pellet stove?
- B
  bryantchristineAug 22, 2025
  If pellets are not feeding into your Travis Industries Pellet stove, consider these potential causes: * The auger may not be primed. Refer to the "Starting Your Heater" section for priming instructions. * The pellet hopper may be empty. Refill it with pellets. * The power button may not be turned ON, or the start button may not be pressed. See "Starting Your Heater". * There may be a power supply issue. Check the household fuse/breaker. * A fuse may have blown. See "Blown Fuse". * The auger flight may be jammed. See "Jammed Auger". * There may be a power outage. Wait until power is restored. * The pellet vent may be blocked. See "Safety Features".
S
shawnstoneAug 26, 2025
Why is there a smoke smell in the room when using my Travis Industries Avalon 900 PS Pellet stove?
- R
  Robin LewisAug 26, 2025
  If you notice a smoke smell in the room while using your Travis Industries Pellet stove, it could be due to: * A momentary power outage, which is normal. See "Safety Features". * The flue not being sealed properly. Refer to the "Installation Instructions". * The automatic safety feature shutting off the stove. See "Safety Features". * The flue system on the insert version not being fully sealed. See "Installation Instructions".
K
Kathy MoralesAug 28, 2025
How to fix a lazy flame with black smoke in my Travis Industries Pellet stove?
- J
  johnny84Aug 28, 2025
  A lazy and dark orange flame with black smoke in your Travis Industries Pellet stove can be caused by: * The AIR CONTROL being set too low. See "Operating Your Heater". * A plugged firepot. See "Check the Firepot". * Bad pellets. See "Poor Quality Pellets". * Clogged exhaust ducts. See "Clean the Exhaust Ducts". * An air leak. See "Air Leaks". * A clogged exhaust system. See "Exhaust Blower".
L
Lisa HopkinsAug 31, 2025
Why does my Travis Industries Avalon 900 PS heater turn off when the hopper is full?
- C
  Cheyenne RoseAug 31, 2025
  If your Travis Industries Pellet stove heater turns off when the hopper is full, it might be due to: * A power outage. See "Safety Features". * The automatic safety feature shutting the stove off. See "Safety Features". * The auger being jammed. See "Jammed Auger".
N
Nicholas RomeroSep 2, 2025
Why does the firepot overfill on startup in my Travis Industries Avalon 900 PS?
- T
  Teresa ThompsonSep 2, 2025
  If the firepot overfills on startup in your Travis Industries Pellet stove, it may be due to: * Lighting the fire starter with the BURN RATE on "HIGH". See "Starting Your Heater". * The fire starter not fully igniting. See "Starting Your Heater". * The AIR CONTROL not being pulled out after the BURN RATE was set to "HIGH". See "Starting Your Heater".
R
Rebecca MacdonaldSep 5, 2025
Why is the exhaust smoky from my Travis Industries Pellet stove, but the flame is okay?
- M
  millerdebraSep 5, 2025
  If the exhaust from your Travis Industries Pellet stove is smoky, but the flame is okay, it could be because: * The heater was just started, which is normal. * The pellets are of poor quality. See "Poor Quality Pellets".
V
vanessa02Sep 8, 2025
What to do if fire starter extinguishes soon after lighting in my Travis Industries Avalon 900 PS?
- P
  Paul LeeSep 8, 2025
  If the fire starter extinguishes soon after lighting in your Travis Industries Pellet stove, it could be because: * The heater was not turned on and the start button pressed. See "Starting Your Heater". * The AIR CONTROL was pulled all the way out while the fire starter was just starting to burn. See "Starting Your Heater".
J
jessica37Sep 12, 2025
Why does the fire go out on low burn on my Travis Industries Pellet stove?
- R
  Regina WallaceSep 12, 2025
  If the fire goes out on low burn in your Travis Industries Pellet stove, it could be due to: * The AIR CONTROL being too far out. See "Operating Instructions". * An air leak. See "Air Leaks".

Travis Industries Avalon 900 PS Specifications

General

Brand	Travis Industries
Model	Avalon 900 PS
Category	Pellet stove
Language	English

Travis Industries Avalon 900 PS - User Manual

Table of Contents

Questions and Answers

Travis Industries Avalon 900 PS Specifications