To Next PageTo Next Page
Need help?Do you have a question about the Travis Industries DVL EmberGlo GSR2 Insert and is the answer not in the manual?
Critical safety warning regarding fire and explosion hazards associated with the appliance.
Step-by-step instructions for responding to a gas leak.
Warnings about hot glass and protecting children from burns.
Important information including serial number, warranty registration, and saving the bill of sale.
Details on appliance testing, listing by Omni Test Labs, and Massachusetts approval.
Overarching warnings about property damage, injury, death, and adherence to instructions.
Guidance on supervising children, preventing burns, and using physical barriers.
Rules for installers, codes, manufactured homes, venting, air, and location.
Rules for operation, part replacement, glass condition, emergency shutoff, and flammable materials.
Lists core features like blower, remote, pilot modes, and installation compatibility.
Details heating capacity, BTU input, electrical rating, and fuel type.
Critical warnings for installers and a checklist of included components.
Recommended sequence for installation and a list of additional materials needed.
Instructions for installing the top convection deflector.
Requirements for fireplace structure, cleaning, and minimum dimensions.
Specific rules for installing in factory-built wood fireplaces, including marking.
Guidelines for hearth extensions and avoiding contact with combustible surfaces.
Instructions and diagram for using leveling legs to ensure the insert is supported and level.
Explains electrical requirements, including the use of an Insert Wiring Kit.
Step-by-step guide for rerouting the appliance's power cord to the side.
Details minimum clearance distances to walls, mantels, and top facing surfaces.
Provides guidelines for mantel depth relative to mantel height above the insert.
Covers requirements for gas line installation, including specific rules for Massachusetts.
Details required pressures and procedures for testing gas pressure.
Details vent kits, installation rules, pipe connections, and termination requirements.
Explains the need for natural draft and factors that can affect appliance drafting performance.
Detailed instructions and diagrams for setting the exhaust restrictor for proper venting.
Instructions for installing and securing the venting system, referencing Dura-Vent.
Diagram showing the location and diameters of the vent intake and exhaust ports.
Illustrates the Inlet & Exhaust Re-Line venting configuration.
Illustrates the Exhaust Only Re-Line venting configuration with cautions.
Procedure for removing and reattaching the vent connector for tight installation scenarios.
Steps for pulling liners, cutting to length, and securing the vent connector.
Discusses testing at various altitudes and the need for air shutter adjustment.
Details requirements and kits for horizontal vent termination in masonry fireplaces.
Information on DuraVent kits for adapting co-linear venting to co-axial pipe.
Instructions for installing different types of surround panels, including notch usage.
Guidance on routing the power cord when using flush-fitting panels.
Step-by-step guide with diagrams for attaching mounting brackets for original panels.
Instructions for bending mounting tabs and attaching surround panels for Ember-Glo units.
Detailed steps for safely removing and re-installing the glass frame, including barrier warnings.
Instructions on how to remove the visual deflector, held by magnets.
A step-by-step checklist covering final installation tasks before operation.
Instructions and visual guides for adjusting air shutters to achieve optimal flame appearance.
Emphasizes reading manual, safety precautions, and remote control warnings.
Instructions on how to program the remote to disable or enable thermostat and other modes.
Identifies the location of the remote control and access points for controls.
Steps to ensure the remote control is properly set up and ready for use.
Steps to synchronize the remote transmitter with the Integrated Fireplace Control (IFC).
Explains how to operate the fireplace directly using the battery holder switch (ON, OFF, REMOTE).
Guides for the initial startup, including curing the paint and observing flame behavior.
Explains the differences between Intermittent Pilot Ignition (IPI) and Continuous Pilot Ignition (CPI).
Explains the 7-day pilot shutoff timer and its application in CPI mode.
Offers strategies like periodic use or thermostat use to prevent the pilot mode from resetting.
General introduction to operating the fireplace using the transmitter.
Explanation of the transmitter display sections and understanding IFC beep signals.
Details how to cycle through and use Manual On/Off, Smart Thermostat, and Standard Thermostat modes.
Instructions on how to cycle through and adjust Flame Height and Blower Speed.
Explains blower operation in Manual Mode, where it remains on even when the burner is off.
Instructions for adjusting accent light and Ember-Glo lights brightness.
Guide to turning the rear burner's comfort control on or off.
Procedure for toggling display units and identifying low battery status.
Detailed instructions for battery replacement and how the unit operates during power outages.
Instructions on activating and deactivating the child-proof feature on the remote.
Descriptions of expected sounds and odors during normal operation.
Guidance on cleaning plated surfaces to prevent etching and maintain appearance.
Step-by-step instructions for accessing and replacing the accent light bulb.
Instructions for replacing the Ember-Glo light bulbs, including bulb type and removal steps.
Steps to remove the media tray to access the bulbs.
Detailed instructions for removing old bulbs and installing new ones, ensuring correct orientation.
A comprehensive procedure for annual servicing, including safety checks and component inspections.
A table listing common issues, their potential causes, and recommended actions before calling for service.
A schematic illustrating the electrical connections and components of the appliance.
Lists part numbers for common replacement components, with cautions.
Displays the safety and listing label information, including clearances, specifications, and warnings.
Outlines the 7-year warranty coverage, conditions, exclusions, and service procedures.
Detailed instructions and warnings for converting the appliance from Natural Gas to Propane.
Steps for installing propane orifices, including identification and correct protrusion.
Procedure for installing the LP pilot orifice after removing the NG orifice.
Instructions for replacing the stock stepper motor with the LP version, ensuring correct orientation.
General guidelines and warnings for installing firebacks, including handling and cleaning precautions.
Instructions for placing the rear fireback into its correct position within the firebox.
Steps for preparing and separating fireback clips for installation.
Instructions for centering the rear fireback and securing it with clips.
Steps for installing the side fireback panels, ensuring proper contact with the rear fireback.
Instructions on installing fireback clips to secure the panels in place.
Steps to reinstall the burner side covers after fireback installation.
Provides warnings and the order of installation for log sets, including conversion and fireback considerations.
Notes that Oak and Birch log sets are similar, differing mainly in paint and texture.
Diagram illustrating the correct placement of the ten logs for the Oak log set.
Diagram illustrating the correct placement of the ten logs for the Birch log set.
Warnings about log fragility and ensuring proper insert placement before starting log installation.
Step-by-step instructions for placing the rear and left logs onto the burner.
Instruction for placing the right log onto the burner grate, ensuring contact.
Instructions on how to apply ember chunks around the burner and grate for a realistic appearance.
Guidance on placing remaining ember chunks to cover exposed metal and perforations.
Instructions for applying rock wool onto the burner to enhance the glow effect.
Instructions for installing ember glass over the perforated area of the grate.
Guidance on using touch-up paint to enhance the realistic appearance of the ember glass.
Instructions for placing the front left log, noting its channel and position on the grate.
Instructions for placing the top right log, aligning its slots with the pins on rear and right logs.
Instructions for placing the center twig, noting its resting points on the log and grate.
Instructions for placing the center log, noting its resting points on the rear log and center twig.
Instructions for placing the right ember chunk.
Instructions for placing the left twig, noting its resting points on the front left log and left log.
Instructions for placing the center-left twig, noting its resting point on the front left log.
Instructions for placing remaining ember chunks to create a realistic appearance.
General| Brand | Travis Industries |
|---|---|
| Model | DVL EmberGlo GSR2 Insert |
| Category | Fireplace Accessories |
| Language | English |
