Traxxas EZ-Peak Dual 2972 User Manual

NiMH/LiPO DUAL CHARGER INSTRUCTIONS
Covers Part #2972
Thank you for purchasing the Traxxas EZ-Peak Dual charger.
This charger features exclusive Traxxas innovations that make
charging batteries easier and safer than ever. If you have any
questions or concerns about your charger, please contact our
customer support team for fast, friendly answers and solutions.
Contact information is at the bottom of this page.
WARNING! For best charging results and your safety, it is essential that you read and
understand these instructions, warnings, and precautions before using the charger.
Charging and discharging batteries has the potential for serious injury and damage to
property. Use care when charging and follow all instructions and cautions.
A
B
C
D
E
F
H
Charge
Status
iD LogoBattery Type
Traxxas High-Current
Connector
Charge
Progress
Charge Rate
(Amps)
A
B
C
D
E
F
G G
H
*Note: Either charger output port can be used independently or both ports can be used
simultaneously to charge. Use the buttons corresponding with the chosen port(s) to
operate the charger.
1. Plug the charger into an AC wall outlet
and connect the battery/batteries
2. Verify the charge settings
Charging Traxxas iD NiMH Batteries
Battery type selected must match the battery type shown on the battery.
The charger will recognize the iD batteries
and show you the charge settings.
Charge Rate Start
Battery Type
HKC15006-R01 150410
TRAXXAS.com
Traxxas, 6200 Traxxas Way, McKinney, TX 75070, Phone: 1-888-TRAXXAS (Toll-free, US only) or 972-549-3000, Fax: 972-549-3011, e-mail: support@Traxxas.com
3. Charging
Press and hold the Start button(s)
for 1 second. The charger will
play a tone, indicating that
charging has started. Press once
to stop. The charger will play a
tone, indicating that charging
has been canceled. The charge
progress LEDs will light as the
battery charges.
Charging
(flashing)
Charge Cycle Progress
4. Charge cycle complete
The charger will play a complete tone, followed by one or two beeps
to indicate channel 1 (left) or channel 2 (right) charging is complete.
The EZ Peak Dual will
trickle charge your NiMH
battery at up to 200mA
for 12 hours after the
charge cycle is complete.
Cycle
Complete
(solid)
A. Start/Stop
B. LiPo Charge Mode Select
C. Battery Type Select
D. Charge Rate Select
E. Charger Output Ports (Traxxas
High-Current Connector)*
F. 2S/3S Lipo Balance Ports
(pull to remove cover)
G. Charge Status LEDs
H. Charge Progress/
Charge Rate LEDs
Identifying iD Batteries LiPo battery shown, NiMH battery similar
Dual Charge Mode

Traxxas EZ-Peak Dual 2972 Specifications

General

Brand	Traxxas
Model	EZ-Peak Dual 2972
Category	Battery Charger
Language	English

Summary

Identifying Traxxas iD Batteries

Traxxas High-Current Connector

Identifies the Traxxas High-Current Connector used for batteries.

Battery Type Identification

Shows how to identify battery types like LiPo and NiMH.

iD Logo Identification

Explains the identification logo on Traxxas batteries.

Charging Traxxas iD NiMH Batteries

Connecting Battery/Batteries

Connect the charger to AC power and plug in the battery/batteries.

Verifying Charge Settings

Confirm that the selected charge settings match the battery.

Initiating Charging

Press and hold the Start button to begin charging.

Charge Cycle Completion

Charger indicates completion with tones and LEDs.

Charging Traxxas iD LiPo Batteries

Connecting Battery/Batteries (LiPo)

Connect the charger to AC power and plug in the LiPo battery.

Verifying Charge Settings (LiPo)

Confirm selected charge settings match the LiPo battery.

Initiating Charging (LiPo)

Press and hold the Start button to begin LiPo charging.

Charge Cycle Completion (LiPo)

Charger indicates completion with tones and LEDs.

LiPo Charging Modes

Storage Charge Mode

Charges/discharges batteries to proper storage voltage for long-term storage.

Fast Charge Mode

Charges batteries without balancing cells, stopping when first cell peaks.

Balance Charge Mode

Balances LiPo cells for maximum capacity, voltage, and battery life.

High Output Mode Charging

Using High Output Mode

Use High Output Mode for faster charging of high-capacity batteries.

Advanced Mode Charging (No iD)

Connecting Batteries for Advanced Mode

Connect main and balance connectors for non-iD batteries.

Entering Advanced Mode

Simultaneously press Start and Charge Rate Select for 2 seconds.

Advanced Mode NiMH Charging

Select NiMH type and charge rate, then start charging.

Advanced Mode LiPo Charging

Select LiPo type and charge rate, then start charging.

Charger Error Codes

Error Code Explanation

Details error codes, their meanings, and recommended solutions.

Warranty Information

Traxxas Electronic Components Warranty

Covers defects in materials/workmanship for 30 days, with exclusions.

Traxxas Lifetime Electronics Warranty

Offers repair services for electronic components after the warranty period.