Triton ta235csl - User Manual

Other manuals for Triton ta235csl

Questions and Answers

B
Brian ThompsonAug 16, 2025
Why is my Triton Saw having poor performance?
- G
  garrisonjonAug 16, 2025
  Poor performance in your Triton Saw can stem from several issues: * The extension lead might be too long or undersized. Use an extension lead that's heavy enough to carry the current. * The blade could be blunt or damaged. Try re-sharpening or replacing the blade. * The motor might be overloaded. Reduce the pushing force on the saw and ensure the cut isn’t closing and pinching the blade. * The tool may be overheating. Turn off the tool, let it cool to room temperature, and inspect and clean the ventilation slots.
L
Lucas GarciaAug 19, 2025
What to do if my Triton ta235csl will not operate?
- S
  sanchezjermaineAug 19, 2025
  If your Triton Saw won't operate, the power lead may not be plugged in. Ensure that the power lead is properly connected to the power supply.
A
Autumn WhiteAug 22, 2025
What to do if the guard on my Triton ta235csl Saw is bent?
- J
  Jean BeanAug 22, 2025
  If the guard on your Triton Saw is bent, straighten it.
J
John ScottAug 26, 2025
What to do if the mechanism of my Triton ta235csl is fouled by sawdust?
- A
  Aaron WardAug 26, 2025
  If the mechanism of your Triton Saw is fouled by sawdust, clean and lightly lubricate the fouled mechanism.
G
Gabriel LiuAug 28, 2025
Why the retractable guard will not close on my Triton ta235csl Saw?
- B
  Becky DelacruzAug 28, 2025
  If your Triton Saw's retractable guard is not closing properly, start by checking the return spring. If it's detached or broken, re-attach or replace it using only genuine Triton replacement parts. Also, inspect the guard itself; if it's bent, try to straighten it, or contact an authorized service center for repair or replacement. Finally, the mechanism might be fouled by sawdust. In this case, clean and lightly lubricate the mechanism.
D
Daniel AguilarAug 31, 2025
Why is my Triton ta235csl showing poor performance?
- P
  Paula Martinez MDAug 31, 2025
  If your Triton Saw is exhibiting poor performance, make sure you are using an extension lead heavy enough to carry the current. Check the blade; if it is blunt or damaged, re-sharpen or replace it. Reduce the pushing force on the saw to prevent motor overload, and ensure the cut isn’t closing and pinching the blade. If the tool is overheating, turn it off and let it cool down, then inspect and clean the ventilation slots.
M
Martha MataSep 3, 2025
What to do if heavy sparking occurs inside Triton ta235csl Saw motor housing?
- L
  Lori JohnsonSep 3, 2025
  If you notice heavy sparking inside the motor housing of your Triton Saw, first, disconnect the power and check the brushes. Remove them and clean or replace if they are not moving freely. If the issue continues, it could be due to a short-circuited or open-circuited armature, or a dirty commutator surface, in which case you should contact an authorized service center for repair or replacement.
C
Cassandra MendezSep 6, 2025
Why is my Triton ta235csl Saw making vibration or abnormal noise?
- N
  Nicole WoodardSep 6, 2025
  If your Triton Saw is vibrating or making abnormal noises, first ensure that the saw blade is fully tightened in the arbor washers. If the problem persists, it may be due to excessively worn moving parts, a mechanical obstruction, or a shorted armature. In these cases, you should contact an authorized service center for repair or replacement.
M
Mrs. Sarah ShawSep 9, 2025
What to do if the motor runs but blade won’t spin on my Triton Saw?
- R
  Rebecca WilliamsSep 9, 2025
  If the motor of your Triton Saw runs but the blade won’t spin, tighten the blade retaining nut and make sure the arbor washers are correctly fitted. If that doesn't solve the issue, it could be due to a broken gear shaft or teeth, which requires repair or replacement by an authorized service center.
Y
ykentSep 12, 2025
How to fix Triton ta235csl Saw depth adjustment not holding?
- E
  Erin AdamsSep 12, 2025
  If the depth adjustment on your Triton Saw is not holding, reposition the Depth Adjustment Locking Lever as described in 'Adjusting the depth locking lever tension'.

Triton ta235csl Specifications

General

Type	Circular Saw
Voltage	230V
Variable Speed	No
Blade Diameter	235mm
Max Cutting Depth at 90°	85mm
No Load Speed	5000 RPM
Dust Extraction	Yes
Blade Bore	30mm
Power Source	Corded
Bevel Angle	0° - 45°