To Next PageTo Next Page
Need help?Do you have a question about the Triumph speed triple 1050 and is the answer not in the manual?
General| Displacement | 1050 cc |
|---|---|
| Transmission | 6-speed |
| Compression Ratio | 12.0:1 |
| Front Tire | 120/70 ZR17 |
| Engine Type | Liquid-cooled, 12-valve, DOHC, in-line 3-cylinder |
| Seat Height | 825 mm (32.5 in) |
| Bore x Stroke | 79 mm x 71.4 mm |
| Fuel System | Multipoint sequential electronic fuel injection |
| Frame | Aluminium beam twin spar |
| Front Brakes | Twin 320mm floating discs, 4-piston radial calipers |
| Wheelbase | 1435 mm (56.5 in) |
Guidelines for effectively using the service manual and understanding its structure.
Explanation of safety and informational symbols used throughout the manual.
General safety advice including handling fuel, electrical work, and component care.
Lists special tools, component specifications, and torque wrench settings.
Explains the importance of maintaining the motorcycle for safety and reliability.
Provides a detailed schedule of required maintenance operations.
Details cylinder head construction and cam cover removal/installation.
Procedures for camshaft removal, inspection, and valve clearance adjustment.
Steps for removing/installing cylinder head, valves, and stem seals.
Steps for removing, inspecting, and assembling the clutch cable.
Procedures for disassembling the clutch and inspecting components.
Procedures for reassembling the clutch components.
Procedures for disassembling and assembling the crankcase halves.
Steps for crankshaft/rod removal, installation, and bearing selection.
Steps for piston removal, wear checks, and cylinder liner installation.
Procedures for removing and inspecting the balancer shaft and its components.
Steps for assembling and installing the balancer shaft and gears.
Procedures for removing, inspecting, and installing the selector shaft, forks, and drum.
Steps for removing and installing the input and output shaft assemblies.
Lists specifications for gears, shafts, and related parts.
Covers engine oil specifications, level checks, changes, and disposal.
Steps for removing, inspecting, and installing the oil pump and sump.
Steps for removing, inspecting, and installing the oil cooler.
Detailed steps for removing the engine from the motorcycle frame.
Procedures for reinstalling the engine into the motorcycle frame.
Covers fuel types, system description, sensors, and actuators.
Procedures for fault detection, DTCs, and using the Triumph diagnostic tool.
Covers coolant properties, level checks, replacement, radiator cleaning, and fan safety.
Steps for removing, installing, and inspecting water pump and thermostat.
Procedures for removing and installing the radiator.
Covers chain adjustment, lubrication, inspection, and wear checks.
Procedures for removing, inspecting, and installing the rear suspension unit and connecting links.
Steps for removing, inspecting, and assembling the swinging arm, drive chain, and final drive.
Covers fork inspection, removal, disassembly, assembly, and oil changes.
Steps for checking, adjusting, removing, inspecting, and installing headstock bearings.
Essential safety warnings and precautions for brake system maintenance.
Covers fluid inspection, pad inspection, caliper, disc, and master cylinder procedures.
Covers fluid inspection, pad inspection, caliper, disc, and master cylinder procedures.
Steps for removing, disassembling, and installing brake master cylinders.
Covers tyre markings, pressures, wear, inspection, and warnings.
Steps for removing and installing the front wheel.
Steps for removing and installing the rear wheel.
Steps for removing, inspecting, and installing wheel bearings.
Inspects frame, footrests, and fixings for damage and wear.
Procedures for removing and installing the seat and side panels.
Procedures for removing and installing the front and rear mudguards.
Covers battery removal, refit, commissioning, charging, and maintenance.
Identification and replacement of fuses and relays.
Steps for removing/installing instrument pack and adjusting headlights.
Steps for removing, inspecting, and installing starter motor and alternator.
