The Trone Zendoro is an electronic bidet toilet designed for enhanced hygiene and convenience. It integrates various automatic functions and adjustable settings to provide a personalized and comfortable user experience.
Function Description:
The Trone Zendoro offers a comprehensive range of bidet functions, including:
- Self-Cleaning Wand: The spray wand automatically cleans itself before and after each use, ensuring optimal hygiene.
- Deodorizer: An integrated deodorizer activates when the seat sensor is engaged, helping to neutralize odors. It can be manually stopped and automatically deactivates after 60 seconds of the user leaving the seat.
- Pre-Rinse: A quick jet of water covers the bowl when the seat sensor is activated, aiding in waste removal.
- Automatic Flush: The toilet can be set to flush automatically after washing and drying, or when the user leaves the seat if no washing has occurred. This feature can be toggled on and off.
- Automatic Opening/Closing Lid: The lid can be configured to open automatically upon approach and close automatically after approximately 3 minutes of no motion detection. This feature is off by default and can be activated or deactivated.
Usage Features:
The Zendoro offers extensive customization and control through its remote and integrated sensors:
- Lid and Seat Control:
- Manual Operation: The lid and seat can be opened and closed by hand. Users are cautioned not to interrupt automatic movement to prevent gear damage.
- Remote Control: Dedicated buttons on the remote allow for opening and closing the lid and seat. If the seat is open, pressing the lid button will close both the seat and lid.
- Foot Sensor: Gently tapping the foot sensor when the lid or seat is closed will open them. The foot sensor cannot be used to close the lid.
- Automatic Operation: The lid can automatically open upon approach and close after 3 minutes of inactivity, if the automatic lid function is enabled.
- Bidet Functions:
- Stop Function: A dedicated "Stop" button immediately ends any active rear wash, front wash, or drying function.
- Rear Wash: Initiated by pressing the "REAR/MOVE" button. Pressing it again activates an oscillating function for increased cleaning area. The rear wash automatically stops after approximately 120 seconds of continuous cleaning.
- Front Wash: Initiated by pressing the "FRONT/MOVE" button. Pressing it again activates an oscillating function. The front wash automatically stops after approximately 120 seconds and transitions to the drying function.
- Drying: Activated by pressing the "DRY/DRYER TEMP" button. The dryer automatically stops after approximately 5 minutes of continuous drying.
- Adjustable Settings:
- Seat Temperature: Five levels of adjustable seat temperature, controlled by the "SEAT TEMP." button.
- Water Pressure: Three levels of adjustable water pressure for washing, controlled by the "Plus" or "Minus" buttons.
- Spray Wand Position: Five levels of adjustable wand position during washing, controlled by the "Up" or "Down" buttons.
- Water Temperature: Five levels of adjustable water temperature for washing, controlled by the "WATER TEMP." button.
- Drying Temperature: Five levels of adjustable drying temperature, controlled by the "DRY/DRYER TEMP" button.
- Eco Mode: Pressing and holding the "STOP" button activates or deactivates Eco Mode. When active, the eco icon appears on the LCD display, and the seat temperature is lowered when the toilet is unoccupied to save energy.
- Night Light: A "LIGHT" button controls the integrated night light.
- Automatic Flush On/Off: The automatic flush function can be toggled on or off by pressing and holding the "FULL FLUSH" button.
- Remote Pairing: The remote control can be paired with the toilet by a specific sequence of button presses, allowing for selection of user codes to prevent interference with multiple units.
Important Technical Specifications:
- Model Number: ZETBCDER-12.WH
- Rated Voltage: 120V, 60Hz
- Rated Power: 1170W
- Power Cable: 7ft
- Flush Volume: 1.6/1.1 GPF (Gallons Per Flush)
- Rough-in Distance: 12"
- Water Pressure Range: 0.09MPa (dynamic water pressure, flow rate 3.96Gal/min or more)
- Warm Air Volume: Over .2m³/min
- Net Weight: 99.2 lbs
- Waterproof Level: IPX4
- Cleaning Time: Normal cleaning is approximately 120 seconds.
- Nozzle Position Adjustment: 5 levels
- Heating Mode: Instant Heat
- Safety Devices: Thermal fuse, Water temperature sensor, Ground protection, Thermostat, Over temperature protection, Leakage protection plug.
- Deodorization: Nano Intelligent Deodorization
Maintenance Features:
- General Cleaning: The toilet bowl and exterior should be cleaned with a soft damp cloth after ensuring the electrical plug is removed. Do not rinse the product with water directly.
- Self-Cleaning Nozzle Maintenance: While not seated, pressing the "REAR/MOVE" button extends the spray wand, allowing it to be disassembled for cleaning with a soft cloth or brush. The "STOP" button retracts the nozzle.
- Steel Mesh Filter Cleaning: If flushing is poor, the steel mesh filter should be cleaned. This involves unscrewing the angle valve nut, removing the filter net, cleaning it with a brush and warm water, and then reinstalling it. Power and water supply should be turned off before cleaning.
- Battery Replacement: The remote control's 9V battery can be replaced by unplugging the DC connector, removing the battery box, replacing the battery, and reconnecting. Users are advised to keep batteries out of reach of children, confirm polarity, and avoid mixing old/new or different battery types to prevent hazards.
Safety Precautions:
The manual emphasizes several safety precautions, including:
- Not touching electrical outlets with wet hands.
- Not pouring liquids onto the electronic outlet or toilet.
- Never attempting to disassemble, repair, or alter the product.
- Not installing the toilet in moving objects.
- Discontinuing use and turning off water/power if the product is broken (e.g., water leakage, smoke, unusual heating/smell, blockage).
- Using only tap water or potable well water.
- Avoiding touching the electrical plug during thunderstorms.
- Preventing the water inlet pipe from contacting the electrical plug/outlet.
- Not damaging the power cable or plug.
- Using specified electrical outlets and wiring.
- Not obstructing the warm air outlet.
- Paying attention to low-temperature scalding, especially for children, elders, persons with disabilities, or those under medication/alcohol influence.
- Not installing in easily wet or high-humidity areas without proper ventilation.
- Connecting to cold water supply only.
- Ensuring the electrical outlet is grounded.
- Following power wire outlet rules.
- Having professionals replace broken power soft wires.
- Not throwing lighted cigarettes or flaming materials into the toilet.
- Not installing in rooms where temperatures can drop below 39.2°F (4°C).
- Not blocking the air outlet.
- Not using excessive force when closing the cover and seat.
- Not intentionally soiling, spraying, or blocking the cleaning nozzle.
- Regularly cleaning dust from the plug with a dry cotton cloth.
- Using only new hose parts provided with the product.
- Keeping the product away from heaters.
- Closing the water supply valve before removing the junction block.
- Draining water and unplugging the unit if away for a long time or transporting/storing in cold conditions to prevent freezing.
Need help?
To Next Page
General