Turf Equipment Z-SPRAY

Questions and Answers

T
Tyler RobertsAug 18, 2025
Why is the engine losing power in my Turf Equipment Z-SPRAY Spreader?
- A
  Alexander LongAug 18, 2025
  If the engine of your Turf Equipment Spreader loses power, there might be several reasons. First, the engine load could be excessive, so try reducing the ground speed. Another cause may be a dirty air cleaner, which requires cleaning or replacement. Check if the oil level in the crankcase is low and add oil if needed. Also, ensure that the cooling fins and air passages for the engine are free from obstructions. Finally, a dirty fuel filter can cause power loss, so replace it if necessary.
L
lisa10Aug 20, 2025
How to fix an uneven spread/spray pattern with my Turf Equipment Spreader?
- F
  Felicia FloresAug 20, 2025
  If your Turf Equipment Spreader is experiencing uneven spread/spray pattern, start by checking if the impeller is dirty or damaged; clean, repair, or replace it as needed. Ensure the gate is properly adjusted. Unclog or replace any clogged nozzles. Also, make sure the hopper screen is clean. Check for material clumps over the gate and ensure the motor shaft agitator pin is present. Finally, verify that the diffuser ramp setting is correct and adjust the control cable position if necessary.
R
ronald73Aug 22, 2025
Why is the engine overheating on my Turf Equipment Z-SPRAY Spreader?
- S
  Sarah MilesAug 22, 2025
  If the engine of your Turf Equipment Spreader overheats, it could be due to several reasons. The engine load might be excessive, so try reducing the ground speed. Also, check the oil level in the crankcase and add oil if it's low. Make sure the cooling fins and air passages for the engine are free from obstructions.
J
Jeremy BallAug 25, 2025
How to troubleshoot why my Turf Equipment Z-SPRAY Spreader engine won't start?
- B
  Bryan Mitchell DDSAug 26, 2025
  If the engine of your Turf Equipment Spreader will not start, starts hard, or fails to keep running, first, ensure that the fuel tank is full. Next, make sure that the throttle control is midway between the “SLOW” and “FAST” positions, and the choke is in the “ON” position for a cold engine or the “OFF” position for a warm engine. Replace the fuel filter if it's dirty. Clean or replace the air cleaner element if it's dirty. Check the electrical connections for good contact, clean connector terminals, apply dielectric grease, and reconnect if they are corroded, loose or faulty. Clean, adjust or replace the spark plug if it's faulty and check the spark plug wire connection.
N
ntaylorAug 27, 2025
What to do if the starter does not crank on my Turf Equipment Spreader?
- D
  Danielle PerkinsAug 27, 2025
  If the starter on your Turf Equipment Spreader does not crank, make sure the interlock key is installed in the OPC. Charge the battery if it does not have a full charge. Check the electrical connections for good contact; clean and reconnect them if they are corroded, loose, or faulty. Replace the fuse if it is blown.
B
bnguyenAug 30, 2025
Why is no material dispensed from the hopper of my Turf Equipment Spreader?
- J
  John EdwardsAug 30, 2025
  If your Turf Equipment Spreader is not dispensing material from the hopper, the hopper screen may be plugged, so clean it. Also, the gate may not be adjusted properly, so adjust the gate.
H
Henry ReidSep 1, 2025
What causes abnormal vibration in my Turf Equipment Z-SPRAY Spreader?
- M
  Mariah ThomasSep 1, 2025
  If your Turf Equipment Spreader experiences abnormal vibration, make sure that the engine mounting bolts are tightened.
E
Emily GomezSep 4, 2025
How to fix a spray wand that doesn't work on my Turf Equipment Z-SPRAY?
- Z
  Zachary BradfordSep 4, 2025
  If the spray wand on your Turf Equipment Spreader does not work, first, ensure that the tank is full. Place the control valve in the “open” position. Clean, repair, or replace the wand if it is clogged or damaged. Unclog or replace the nozzle if it is clogged. Press the trigger. Clean, repair, or replace the hoses if they are clogged or damaged. Reconnect the hose if it is not connected to the wand. Unkink the hose if it is kinked.
D
Douglas WilsonSep 6, 2025
What should I check if my Turf Equipment Spreader does not drive?
- C
  Crystal VasquezSep 6, 2025
  If your Turf Equipment Spreader is not driving, ensure that the bypass valve is tightened securely.
R
Rodney HarrellSep 9, 2025
How do I troubleshoot no front spray or poor output on my Turf Equipment Z-SPRAY?
- L
  Lauren GarciaSep 9, 2025
  If your Turf Equipment Spreader has no front spray or poor output, start by filling the tank. Then, clean, repair, or replace the strainer if it is clogged or damaged. Clean, repair, or replace the pump if it is clogged or damaged. Unclog or replace the nozzles if they are clogged. Clean, repair, or replace the hoses if they are clogged, kinked, or damaged. Turn on the spray. Adjust the pressure and speed. Follow the chemical manufacturer’s recommendation for the spray mixture. Inspect the system and clean, repair, or replace components as needed if the spray system is leaking or sucking air.