To Next PageTo Next Page
Need help?Do you have a question about the Tuuci 1005376 and is the answer not in the manual?
Remove all packaging from in and around the umbrella before proceeding with installation.
Pull pin from cam lock and lift the handle to unlock the umbrella for further steps.
Slide the beauty cover and umbrella over the security stem after leveling.
Lock umbrella down by pushing cam lock handles and securing with pins.
Remove protective bubble wrap and elastic rope from shipping as trolley carts are tightened.
Install the second canopy frame using 3/8" bushings and screws, applying loctite.
Connect long and short arms wind stabilizers to the respective trolley carts.
Mount the electrical sleeve to the scissor bracket using a bushing and flat head screw.
Connect the cable from the electrical sleeve to the scissor cable.
Push the cable and connector through the scissor grommet hole.
Plug the umbrella cord into a 220V receptacle; the TUUCI logo will backlight.
Press the Power button; it lights red when ON, and light/heater icons light white.
Ensure the gear lock button is in the top (unlocked) position before turning the crank.
Insert and rotate the crank handle counter-clockwise until the cable connector aligns.
Connect the cable connector to the trolley bracket with the security pin for each canopy.
Gently separate each rib individually from the center hub approximately 10 inches.
Ensure the umbrella is level for safety and proper operation of lights and heaters.
Press the light bulb icon to turn on LED lights; color changes to blue when ON.
Press the heater icon to turn on heaters; color changes to blue when ON.
Press the heater icon to turn off heaters; it flashes for 2 minutes before turning white.
Press the light bulb icon to turn off LED lights; color changes to white when OFF.
Press the power button on the control panel to turn off the umbrella.
Close the umbrella with the tie-back when not in use, especially in high winds.
Allow heaters at least 10 minutes to cool down before closing the umbrella.
Press the Power button to shut down or interrupt any function, turning off indicator lights.
Power button flashes yellow if umbrella is not level; functions are inactive until level.
Press and hold Power button for 5 seconds to activate lock-out, preventing unauthorized access.
Heaters automatically turn off after 2 hours of operation for safety.
Details electrical requirements for light units and heaters, including voltage, amps, and watts.
Provides crucial safety guidelines for assembly, operation, and maintenance.
This document describes the installation, operation, and maintenance of a dual canopy umbrella with integrated lights and heaters.
The device is a dual canopy umbrella designed to provide shade, lighting, and heating. It features integrated Ambia LED lights and heaters within each canopy. The umbrella is operated via a control panel and includes safety features such as emergency shut-down, automatic heater turn-off, and a lock-out feature for unauthorized users. It is designed for outdoor use and requires electrical power for its lighting and heating functions.
Step 1: Unpacking Remove all packaging from in and around the umbrella.
Step 2: Unlocking the Umbrella Pull the pin from the cam lock and lift the handle to unlock the umbrella.
Step 3: Mounting the Canopy and Beauty Cover Once the stem is leveled using the base installation instructions, slide the beauty cover and umbrella over the security stem (which is included with the umbrella). It is crucial to ensure that cables are not pinched when inserting the umbrella over the security stem and when installing the beauty cover.
Step 4: Locking the Umbrella and Installing Beauty Covers Lock the umbrella down by pushing the cam lock handles into the down position and securing them with pins. Mount the electrical beauty covers over the control boxes.
Step 5: Preparing for Dual Canopy Frame Installation For shipping purposes, trolley carts are tightened with elastic rope. Remove the protective bubble wrap and elastic rope from the electrical sleeve.
Step 6: Installing the Second Canopy Frame Install the second canopy frame using the 3/8" bushings and screws. Add a drop of provided Loctite to the end of the screw threads for secure fastening.
Step 7: Connecting High Wind Stabilizers (If Applicable) If high wind stabilizers are applicable, connect them as follows: a. Mount long arms wind stabilizers to the lower trolley cart. b. Mount short arms wind stabilizers to the upper trolley cart. Again, add a drop of provided Loctite to the end of the screw threads.
Step 8: Mounting the Electrical Sleeve Mount the electrical sleeve to the scissor bracket using a 3/8" bushing and a 3/8"-16 flat head screw. Apply a drop of provided Loctite to the end of the screw threads.
Step 9: Connecting Electrical Cables Connect the cable from the electrical sleeve to the scissor cable.
Step 10: Routing Cables Push the cable and connector through the scissor grommet hole.
Step 11: Power Connection Plug the umbrella's cord into 220V receptacles. The TUUCI logo on the control panel will be backlit in white when the umbrella is properly plugged into the power source.
Step 12: Turning On the Umbrella Press the Power button on the control panel to turn on the umbrella. The button will be backlit in red when power is ON. The light icon and heater icon on the control panels will also be backlit in white.
Step 13: Preparing for Crank Handle Operation Ensure the gear lock button is in the top (unlocked) position before turning the crank handle.
Step 14: Connecting the Cable Connector Insert and rotate the crank handle counter-clockwise until the cable connector aligns with the cable bracket. It is important to maintain tension on the cable connector while turning the crank counter-clockwise, as the canopies and umbrella will remain closed during this step.
Step 15: Fastening Cable Connector for Each Canopy For each umbrella canopy: a) While the umbrella is still closed, ensure the telescope is fully extended from the mast. b) Pull the security pin from the trolley car bracket. c) Pull the cable connector so it aligns with the trolley car bracket. d) Fasten the cable connector to the trolley bracket with the security pin.
Step 16: Separating Ribs Gently separate each rib individually from the center hub by approximately 10 inches. Do not force if a rib does not move easily; inspect the product for additional packaging.
Turning On Lights and Heaters
Closing Umbrella Canopies
Important Note for Closing: The umbrella should not be closed entirely until all heaters have cooled down. Allow at least 10 minutes for heaters to cool. Close the umbrella during consistent wind conditions that exceed 25mph.
Emergency Shut-down or Interrupt Feature Press the Power button on the control panel to shut down or interrupt any function (Ambia LED lights and heaters). The red light on the Power button will turn OFF, and the white lights on the heater and light icons will turn OFF. Press the Power button again to turn the umbrella back ON.
Control Panel Indicator for Unlevel Umbrella If the umbrella is not level (tipped or tilted), the Power button will flash yellow, and all functions (Ambia LED lights and heaters) will be inactive. The TUUCI logo will not be backlit. Once the umbrella is level, it will return to a powered-down state with the TUUCI logos backlit in white and all other functions OFF. Press the Power button to turn on the umbrella, then activate the desired functions.
Lock-out Unauthorized Users Feature To prevent unauthorized access, press and hold the Power button for 5 seconds. All functions (Ambia LED lights and heaters) will maintain their original ON or OFF state. The Power button will be solid yellow when activated. To turn off the lock-out feature, press and hold the Power button for 5 seconds again. Users will regain access to turn ON-OFF various functions. If the Power button is pressed during a lock-out condition, activating the emergency shut-down or interrupt feature will turn off Ambia LED lights and heaters, and all icon button lights will be OFF, except for the TUUCI logos.
Heater Automatic Turn Off Safety Feature As a safety feature, the heaters on the Automated Umbrella will automatically turn off after 2 hours of operation. To turn the heaters back on, press the heater icon button.
Electrical Specs (Dual Canopy Umbrella) This umbrella requires two electrical circuits, one for each canopy side. Each circuit consists of one light unit and two heaters, totaling two light units and four heaters.
Specifications per Circuit:
North America Version:
Europe Version:
Customer Connection: Customer must connect to a protected power source circuit with proper Current Rating "Amps", near the umbrella, using an above-ground Junction box, according to their local electrical codes and regulations.
CAUTION:
General