Twiins D3 - TWIINS D3 Technical Details; TWIINS D3 Care and Maintenance

11
Intercom pairing with a different Twi-
ins
®
D1, Twiins
®
D2 or a different Blue-
tooth
®
audio receiver.
Dual Link: Pairing as an intercom while maintaining
hands-free functionality:
•Completepairingwiththephoneasdescribedinthe
paragraph above “Pairing to a mobile phone or GPS
navigator”.
•SwitchoffBluetooth
®
on the phones.
•Makesurebothdevicestobepairedareswitchedoff.
•Pressandholdthecontrolbutton(1b)oftheTwiins
®
D3 device until the LED indicator begins flashing in Red
and Blue.
•Pressandholdthecontrolbutton(1b)oftheTwiins
®
D1 or Twiins
®
D2 device until the LED indicator begins
flashing in Red and Blue. If you are using a different de-
vice, put it in pairing mode.
•Brieypressthecontrolbutton(1b)oftheTwiins
®
D3
device once. After a few seconds, both devices will pair
and intercom functions will be activated. Once paired,
it is recommended for you to switch off the Twiins
®
D3
device and switch it back on so that it operates cor-
rectly with your phone and as an intercom.
The other intercom device will receive an acoustic warn-
ing signal.
•Activate Bluetooth
®
on the phones again. Depend-
ing on the phone, it will automatically detect the device
paired. Otherwise, you will need to select it manually.
NOTE: When two Twiins
®
devices are in intercom mode,
incoming call functionality with their respective mobile
phones will be maintained. In case a call is received,
intercom functionality will stop and resume once the call
has ended.
Single Link: Pairing as an intercom only (without
hands-free features):
•Makesurebothdevicesareswitchedoff.
•Pressandholdthecontrolbutton(1b)oftheTwiins
®
D3 device until the LED indicator begins flashing in Red
and Blue.
•Pressandholdthecontrolbutton(1b)oftheTwiins
®
D1 or Twiins
®
D2 device until the LED indicator begins
flashing in Red and Blue. If you are using a different de-
vice, put it in pairing mode.
•Brieypressthecontrolbutton(1b)oftheTwiins
®
D3
device once. After a few seconds, both devices will pair
and intercom functions will be activated. Once paired,
it is recommended for you to switch off the Twiins
®
D3
device and switch it back on so that it operates cor-
rectly with your telephone and as an intercom.
The other intercom device will receive an acoustic warn-
ing signal.
Intercom functions:
Activating and deactivating intercom functions be-
tween two Twiins® devices: once both Twiins
®
devices
have been paired and switched on, press the control
button (1b) of the Twiins
®
D3 for two seconds to activate
or deactivate intercom functionality.
Adjusting the volume for intercom functions: you can
adjust the volume by briefly pressing the control button
(1b). It will then cycle through three levels: LOW < ME-
DIUM < HIGH < LOW…
Technical Specifications
Bluetooth
®
: 2.1 Class 2
Profiles: A2DP stereo, HSP, HFP, EDR
Intercom frequency: 2.4 GHz
Battery: Lithium polymer, allowing for up to 7 hours of
talk time and 200 hours of standby time (depending on
use and configuration of the device)
Care and maintenance
The Twiins
®
D3 device uses components with the lat-
est technology and is manufactured to high standards.
To keep your device from inadvertently becoming dam-
aged, please read the following recommendations care-
fully:
•Do notattempt toopen any ofthe system compo-
nents, since the electronic parts inside it may become
damaged. Do not attempt to open or change the bat-
tery as it may be dangerous.
•KeeptheTwiins
®
D3 out of the reach of children.
•KeeptheTwiins
®
D3 in a dry place. Humidity and con-
densation may damage the electronic circuits.
•Avoidexposingthedevicetoextremetemperatures.
Intense cold may create condensation inside the com-
ponents as these warm up. Extreme heat may damage
the battery, circuits or casings.
•Donotdrop,hitorbendthecomponentsastheinter-