EasyManua.ls Logo

Twin Disc TECHNODRIVE TM 880A - User Manual

Twin Disc TECHNODRIVE TM 880A
54 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
MTM 170-880A - 1st edition - 03.16
Release 02-03/16
1
MANUALE D’USO - OPERATING MANUAL - MANUEL DE SERVICE
- BEDIENUNGSANLEITUNG - USO Y MANUTENCIÓN
TM 880A
MG 5055A
TM 170
MG 5020SC

Table of Contents

Questions and Answers

  • A
    Allison GarciaAug 8, 2025
    What to do if the gear is not engaged in Twin Disc DC Drives?
    • G
      gail15Aug 8, 2025
      If the gear is not engaged in your Twin Disc DC Drives (version with electric control valve), start by checking the battery to ensure there's a power supply. If the power supply is less than 10V, inspect the engine alternator and use the emergency bypass valve. Also, check for rust on the contacts and clean them if necessary. Inspect the contacts and wires for any breaks and repair them. Finally, the valve may be blocked, in this case replace it or call a service center.
  • K
    Kelly MaloneAug 12, 2025
    Why is my Twin Disc DC Drives shifting slowly?
    • S
      Stacie RodriguezAug 12, 2025
      If you notice slow shifting in your Twin Disc DC Drives, it could be due to a stuck control valve, in this case you should consult a service center. Another potential cause is the selector control linkage, which may need adjustment. Additionally, ensure that the oil level is adequate and top it up if it is low.
  • R
    Rebecca KeithAug 16, 2025
    What to do if Twin Disc DC Drives are hard shifting?
    • A
      Ashley ThompsonAug 16, 2025
      If you experience hard shifting with your Twin Disc DC Drives, the control valve might be stuck, so you should consult a service center. Another possible cause is the selector control linkage, which may require adjustment.
  • M
    Mark MorrisAug 20, 2025
    Why is the oil pressure too low in Twin Disc DC Drives?
    • G
      gonzalezbrianAug 20, 2025
      If the oil pressure is too low in your Twin Disc DC Drives, several factors could be the cause. The control valve may be dirty, so you should consult a service station. The control valve might also be clogged, requiring removal and cleaning. Check the filter o-ring for damage and replace if needed. Ensure the oil level is correct and restore it if it's too low. A failure in the oil pump or broken O rings on the clutch shaft may also be responsible, so you should consult a service station.
  • N
    Nancy WaltersAug 26, 2025
    What causes water and oil to mix in Twin Disc DC Drives?
    • P
      patrick95Aug 26, 2025
      If you find water and oil mixed in your Twin Disc DC Drives, it's likely due to a damaged oil cooler, so you should consult a service station.
  • J
    John YoungAug 30, 2025
    What causes too high oil pressure in Twin Disc DC Drives?
    • T
      Thomas FischerAug 30, 2025
      If the oil pressure is too high in your Twin Disc DC Drives, the control valve may be dirty. You should remove the valve and clean it.
  • A
    Ashley ArnoldSep 2, 2025
    What to do if neutral is not engaged in Twin Disc DC Drives?
    • C
      charles09Sep 2, 2025
      If neutral is not engaged in your Twin Disc DC Drives (version with electric control valve), it could be due to a blocked valve, in this case replace it or call a service center. It might also be caused by a damaged clutch, so replace it or call a service center.

Twin Disc TECHNODRIVE TM 880A Specifications

General IconGeneral
BrandTwin Disc
ModelTECHNODRIVE TM 880A
CategoryDC Drives
LanguageEnglish