Need help?Do you have a question about the Tyco Fire Protection Products FAST2000/2 and is the answer not in the manual?
Safety precautions for the FAST2000/2 system, power supply, and battery usage.
Warranty limitations and constraints regarding unauthorized repairs or modifications.
Details the 19" modular system design, rack configurations, and module placement.
Describes standard 19" racks for modules, including height and width.
Explains connections via 64-pin Euro connectors, ribbon cables, and 10-pin connectors for modules.
Details system power from mains and batteries, including monitoring circuits.
Explains connection to loop modules and protocols used.
Lists System Sensor devices, addressing, and analogue detector behavior.
Lists automatic System Sensor loop devices.
Lists non-automatic System Sensor loop devices.
Lists Tyco MZX series loop devices and their addressing.
Lists automatic Tyco MZX loop devices.
Lists non-automatic Tyco MZX loop devices.
Explains typical loop configuration and continuity checks.
Details loop scanning and scan time calculation.
Explains downloading device type info for loop modules.
Provides formula and example for calculating scan times.
Introduces modules dedicated to extinguishing systems.
Describes conditions for gas release and time delays.
Explains the "Hold"-input function for emergency stop.
Details the main intelligent module handling monitoring and control.
Monitors power supply and batteries.
Monitors power supply and batteries.
Interface board for German fire brigade panels.
Updated interface board for German fire brigade panels.
Board providing relays for system status reporting.
Interface card for connecting printers.
Module delivering 8V DC power to other modules.
Man-machine interface module with LCD display.
Power supply unit used until 2008.
Power supply unit used since 2008.
Loop module for Tyco detectors.
Termination board for the LM-32TX module.
Loop module for detection areas.
Termination board for detection areas.
Loop module for extinguishing areas.
Termination board for extinguishing areas.
Termination board with stepper motor output.
Module for monitoring stepper motor systems.
Module for supervising and controlling extinguishing agent storage.
Termination board with one output and inputs.
Termination board with two outputs and inputs.
Termination board with stepper motor output.
Interface unit for processor units and output cards.
Relay output termination board.
Open collector output termination board.
Module providing zone indication for alarms and faults.
Module for overriding tripping functions.
Board for communication between panels.
Board for converting CM-32 serial to RS422/RS485.
Board for converting CM-32 serial to RS232.
Board for converting CM-32 serial to Signalco 30mA.
Board for converting CM-32 serial to fibre optic signals.
RS232 interface card.
Explains the yellow LED indicating faults or isolation of the fire brigade circuit.
Explains the yellow LED indicating faults or isolation of alarm bell circuits.
Explains the yellow LED indicating power supply faults.
Lists available terminal boards for the CM-32.
Provides block diagram of CM-32/2 and lists LED functions/colors.
Describes connectors for external cards and modules on CM-32.
Details jumper settings for boot device, mode config, and serial ports.
Lists supply voltage, current consumption, and dimensions for CM-32.
Details card's connections and 24V outputs.
Shows pin configurations for terminal block J1 and connector J2.
Specifies fuse data for CM-32T module.
Lists voltage output, current consumption, and dimensions.
Describes card's connections and power source switching.
Explains DIP switch S1 function for CM-32T2 setup.
Details LED indicators for system status on CM-32T/2.
Shows terminal block J1 and relevant pins on header J2.
Specifies fuse data for CM-32T/2.
Lists input voltage, output voltage, current, battery type, and dimensions.
Details pin configurations for terminal blocks J1 and J2.
Specifies fuse data for CM-32F.
Lists operating voltage, current consumption, and dimensions.
Shows pin configurations for terminal blocks J3 and J2.
Specifies fuse data for CM-32F/2.
Lists operating voltage, current consumption, and dimensions.
Explains the function of output relays and monitored fault output.
Details pin configurations for terminal block J1 and ribbon cable connector.
Lists operating voltage, current consumption, and relay ratings.
Outlines the inputs and outputs of the PM-32 module.
Describes module's connectors and optional power source.
Lists supply voltage, current consumption, and dimensions.
Lists connectors for external cards and modules.
Lists supply voltage, current consumption, and dimensions.
Explains setting LM-32TX module's address via software.
Details module's electronics, MCU, memory, interfaces, and power.
Explains external connections via 64-pin edge connector.
Refers to chapter 9 for signals on LM-32D connector.
Lists supply voltage, current consumption, and dimensions.
Outlines connection points for LM-32TXT.
Details detection circuit connections, length, resistance, capacitance.
Explains ten auxiliary inputs for monitoring extinguishing systems.
Describes terminals for two monitored sounder outputs.
Explains outputs for controlling valves with monitoring.
Details 24V power supply connection points.
Describes connection between LM-32TXT and LM-32TX.
Details LED indicators for status and communication.
Specifies fuse data for sounder outputs.
Explains setting LM-32D card address using DIP switch.
Block diagram of LM-32D and its interaction with modules.
Details external connections via 64-pin connector and LED board.
Refers to appendix A for LM-32D connector signals.
Lists supply voltage, current consumption, and dimensions.
Outlines connection points for LM-32DT.
Details detection circuit connections, length, resistance, capacitance.
Explains three auxiliary inputs for input monitoring.
Describes terminals for two monitored sounder outputs.
Details 24V power supply connection points.
Describes connection between LM-32DT and LM-32D.
Specifies fuse data for sounder outputs.
Lists voltage, current consumption, and dimensions.
Explains setting LM-32E card address using DIP switch.
Block diagram of LM-32E and its power supply.
Refers to appendix A for LM-32D connector signals.
Lists supply voltage, current consumption, and dimensions.
Outlines connection points for LM-32ET.
Details detection circuit connections, length, resistance, capacitance.
Explains six auxiliary inputs for input monitoring.
Describes terminals for two monitored sounder outputs.
Explains valve outputs for controlling zone and CO2 stop valves.
Details 24V power supply connection points.
Describes connection between LM-32ET and LM-32E.
Specifies fuse data for sounder outputs.
Lists voltage, current consumption, and dimensions.
Outlines connection points for LM-32SCT.
Details detection circuit connections, length, resistance, capacitance.
Explains six auxiliary inputs for input monitoring.
Describes terminals for two monitored sounder outputs.
Explains valve outputs for controlling zone and CO2 stop valves.
Details 24V power supply connection points.
Describes connection between LM-32SCT and LM-32E.
Specifies fuse data for sounder outputs.
Lists voltage, current consumption, and dimensions.
Explains data shifting and port configuration.
Details regulator circuit, shift registers, and driver.
Explains how IO-32 card is controlled by LM-32D/E or CM-32.
Details 64-pin Euro connector and 26-pin connector for modules.
Lists PCB dimensions, supply voltage, and current consumption.
Explains accessing relays via lines based on jumper settings.
Shows pin configurations for ribbon cable connectors.
Lists terminal block connections for relays.
Lists supply voltage range.
Lists terminal block connections for outputs.
Outlines connection points for CM-32CTCB2.
Details power terminal block J4 for 24V supply.
Describes ribbon cable connection to CM-32 serial channels.
Details driver module connectors J1 and J2.
Details jumper block LK1 for selecting driver board connections.
Outlines connection points for CM-32CTCM422.
Details driver module connector J1.
Explains terminal block J2 for RS422/RS485 connections.
Describes LEDs indicating serial channel activity.
Details jumper block LK1 for break signal transmission.
Lists input voltage, current consumption, resistor, and dimensions.
Outlines connection points for CM-32CTCM232.
Details driver module connector J1.
Explains terminal block J2 for RS232 signal levels.
Details ribbon cable connector J3 for RS232 signals.
Describes four LEDs indicating serial channel traffic.
Details jumper block LK1 for break signal transmission.
Lists input voltage, current consumption, and PCB dimensions.
Outlines connection points for CM-32CTCM1.
Details driver module connector J1.
Explains terminal block J2 for Signalco 30mA communication.
Describes two LEDs indicating serial channel traffic.
Details jumper blocks LK1 for monitoring and LK2 for 30mA driver.
Lists input voltage, current consumption, and PCB dimensions.
Outlines connection points for CM-32CTOPT1.
Details driver module connector J1.
Describes fibre optic connectors for cable connection.
Describes two LEDs indicating RX and TX traffic.
Details jumper blocks LK1 and LK2 for current adjustment and break signal.
Lists PCB dimensions and cable specifications.
Emphasizes following installation drawings and local codes.
States mechanical installation must follow site-specific drawings.
Details electrical installation requirements, cable connections, and earthing.
Explains system power supply, battery supervision, and cable connections.
Describes loop connection to LM-32DT/LM-32ET, noting polarization.
Details auxiliary inputs for monitoring signals.
Describes terminals for two monitored sounder outputs.
Explains four output relays on CM-32R for system status reporting.
Details how relays are controlled by Cause & Effect.
Explains valve outputs with open/short circuit monitoring.
Describes standard inputs/outputs for fire brigade panels using CM-32F.
Details the CM-32P RS-232 interface card.
States detection circuits must always be configured as loops.
Advises disconnecting output devices during testing.
Advises disconnecting inputs after testing.
Emphasizes keeping detailed records of hardware and software configurations.
Describes the procedure for powering up the system.
Details connecting and switching on the charger, checking indicators.
Explains battery cut-off relay function and testing.
Outlines loop commissioning, including wiring and electrical checks.
Details visual checks, loop resistance, and continuity tests.
Describes electrical checks, simulating faults, and verifying readings.
Provides procedure for connecting and testing sounder outputs.
Explains connecting and testing dedicated control relays.
Details procedure for checking fault output connection.
Outlines procedure for checking zone valve output connection.
Provides procedure to check and connect control relay outputs.
Details how to test auxiliary inputs.
Describes checks for the fire brigade panel interface.
Advises on connecting RS-232 equipment.
Outlines the procedure for initiating the panel.
Describes performing a complete system test after commissioning.
Explains system self-monitoring for power, circuits, and microprocessors.
Details automatic signal level comparison for false alarm reduction.
Explains how fault alarms are displayed and how to get more information.
Mentions system information sources.
Provides guidance on a methodical approach to finding and correcting faults.
Lists symptoms, causes, and actions for a non-functional DM-32.
Lists symptoms, causes, and actions for a non-functional CM-32.
Lists symptoms, causes, and actions for power supply failures.
Describes symptoms, causes, and troubleshooting for alarm bell open circuits.
Describes symptoms, causes, and troubleshooting for alarm bell short circuits.
Details symptoms, causes, and troubleshooting for detection loop open circuits.
Details symptoms, causes, and troubleshooting for detection loop short circuits.
Describes symptoms, causes, and troubleshooting steps for earth faults.
Recommends a scheduled service and maintenance program.
Outlines the purpose of the main service, recommending it annually.
Details checks for front panel, keys, display, and indicators.
Describes visual checks of enclosures, wiring, terminals, fuses, PCBs.
Details checking charger output voltage and battery voltage.
Explains checking communication bus activity and voltage.
Details checking zoning, device types, and loop continuity.
Describes checking sounder circuits for faults and alarm conditions.
Details simulating activation conditions to check relay operation.
Describes checking auxiliary inputs and panel actions.
Details testing fire brigade panel activation and reset.
Explains the purpose of minor service, recommending it bi-monthly.
Lists checks for front panel, keys, display, and switches.
Details checks for charger voltage, battery voltage, and fault reporting.
Describes checking devices for faults and testing selected devices.
Details simulating alarm conditions to check sounder operation.
Describes checking signal transmission to calling equipment.
Explains the default response to a fault alarm.
Details default actions for fire alarm inputs.
States no default response to prewarnings.
Notes auxiliary inputs are not used by default unless custom programmed.
Provides a detailed breakdown of signals on the CM-32's 64-pin connector.
Lists signals on the LM-32's 64-pin connector.
Lists signals on the EM-32's 64-pin connector.
Lists signals on the IO-32's 64-pin connector.
Introduces loop loading parameters and calculation methods.
Discusses the use and purpose of short-circuit line isolators.
Explains maximum addressable units and permissible loading.
Discusses considerations for LPS800 modules regarding operating range.
Covers cable requirements, types, and length for MX Digital Loops.
States cable requirements must meet local standards.
Lists various fire-resistant cable types.
Provides guidelines for cable lengths.
Discusses the importance of cable screens.
Explains voltage drop calculations.
Refers to pages 8-12 for calculation sheets.
Provides a sheet for calculating loop loading per loop.
Provides a sheet for calculating load between line isolators.
General| Brand | Tyco Fire Protection Products |
|---|---|
| Model | FAST2000/2 |
| Category | Fire Extinguisher |
| Language | English |
To Next Page