U-Line H-9996 - User Manual

To Next Page

PAGE 1 OF 9 0322 IH-9996

1-800-295-5510

uline.com

LED WALL PACK

H-9996

PARTS

SAFETY

WARNING! This product may present a shock or

fire hazard if improperly installed or attached

in any way. Product should be installed in

accordance with these instructions, current

electrical codes and/or the current National

Electric Code (NEC).

CAUTION! Ensure supply voltage is the same as

the rated luminaire voltage. Do not operate in

ambient temperatures above those indicated

on the luminaire nameplate. Do not install

where operating temperatures exceed

ambient temperature range. To avoid the risk

of fire, explosion or electric shock, this product

should be installed, inspected and maintained

by a qualified electrician only in accordance

with all applicable electrical codes. Be certain

electrical power is off before and during

installation and maintenance.

For supply connections, use wire rated for at least 194°F.

NOTE: Input is 120-277VAC.

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

• This device may not cause harmful interference.

• This device must accept any interference received,

including interference that may cause undesired

operation.

Para Español, vea páginas 4-6.

Pour le français, consulter les pages 7-9.

LED Wall Pack x 1 Plastic Anchor x 3 Wire Nut x 3Mounting Screw x 3

TOOLS NEEDED

DrillPhillips Screwdriver Drill Bit

Main Page

Need help?

Do you have a question about the U-Line H-9996 and is the answer not in the manual?

This document describes the Uline H-9996 LED Wall Pack, a lighting fixture designed for outdoor use. The manual provides instructions for installation, safety guidelines, and technical specifications in English, Spanish, and French.

Function Description

The Uline H-9996 LED Wall Pack is a solid-state lighting fixture designed for long-lasting, high-efficiency illumination with minimal maintenance. It is intended for use as an outdoor wall-mounted light. The fixture can be mounted directly to a wall or to a junction box. It is suitable for use in wet locations and can operate in a wide range of ambient temperatures. The product is designed to provide reliable lighting while adhering to safety and regulatory standards, including FCC rules for digital devices.

Important Technical Specifications

Model Number: H-9996
Input Voltage: 120-277VAC (100V-277V, 60 Hz nominal AC power supply, with no variation in light output due to its internal power factor corrected source).
Operating Temperature Range: -40°C to 40°C (-40°F to 104°F).
Wiring: For supply connections, use wire rated for at least 194°F (90°C).
Compliance:
- FCC Rules Part 15 (Class B digital device) for reasonable protection against harmful interference in a residential installation.
- Current electrical codes and/or the current National Electric Code (NEC).
Mounting: Wall mount or junction box mount.

Usage Features

Easy Installation: The manual provides detailed, step-by-step instructions for both wall mounting and junction box mounting, including diagrams.
- Wall Mount: Involves removing the front cover, aligning the back plate, marking and drilling holes, inserting plastic anchors (if needed), and securing the back plate with mounting screws. Wiring connections are made, and then the front cover is reassembled and sealed.
- Junction Box Mount: Requires removing the front cover, drilling holes on the back plate for the junction box, removing the center knockout, feeding supply wires through, mounting the back plate to the junction box, connecting wires, and finally reassembling and sealing the front cover.
Versatile Power Supply: The unit can be used with any nominal 100V-277V, 60 Hz AC power supply, and its internal power factor corrected source ensures consistent light output.
Standard Photocell Compatibility: The unit can be mounted to a standard photocell with a housing, making it suitable for public lighting applications.
Durable Design: The LED technology ensures long-term performance and high efficiency.
Interference Management: The device is designed to minimize harmful interference and accept any received interference, which may cause undesired operation. In case of interference, troubleshooting steps include reorienting/relocating the receiving antenna, increasing separation between equipment and receiver, or connecting the equipment to an outlet on a different circuit.

Maintenance Features

Qualified Electrician Required: Installation, inspection, and maintenance of this product should only be performed by a qualified electrician in accordance with all applicable electrical codes to avoid risks of fire, explosion, or electric shock.
Power Disconnection: Electrical power must be turned off at the circuit breaker or fuse before and during installation and maintenance to prevent possible electrical shock.
Regular Inspection: The product should be inspected and maintained regularly to ensure safe and proper operation.
Troubleshooting Guidance: The manual provides guidance for addressing potential issues such as harmful interference, suggesting steps like reorienting antennas or adjusting distances between devices.
Customer Support: Uline Customer Service is available for assistance at 1-800-295-5510.

Safety Information

Shock/Fire Hazard Warning: Improper installation or attachment can lead to shock or fire hazards. The product must be installed according to the provided instructions, current electrical codes, and the National Electric Code (NEC).
Voltage Verification: Always ensure that the supply voltage matches the rated luminaire voltage.
Temperature Restrictions: Do not operate the fixture in ambient temperatures outside the specified range (-40°C to 40°C) or install it where operating temperatures exceed this range.
FCC Compliance: The device complies with Part 15 of the FCC Rules, meaning it is designed not to cause harmful interference and must accept any interference received.
Save Instructions: Users are advised to save the instructions for future reference.

Tools Needed for Installation

Phillips Screwdriver
Drill
Drill Bit

Parts Included

LED Wall Pack (x1)
Mounting Screw (x3)
Plastic Anchor (x3)
Wire Nut (x3)

U-Line H-9996 Specifications

General

Brand	U-Line
Model	H-9996
Category	Outdoor Light
Language	English