Why is the 'Ice' indicator on my Ugur Ice Maker?
If the "Ice" indicator is illuminated on your Ugur Ice Maker, this means the ice basket is full. To resolve this, simply remove the ice from the ice basket.
How to fix a water leak in my Ugur UBM 20?
If your Ugur Ice Maker is leaking water, ensure that the water drainage cap is properly tightened. Tighten the drainage cap to stop the leakage.
What to do if the 'Water' indicator is on in my Ugur Ice Maker?
If the "Water" indicator is illuminated on your Ugur Ice Maker, it means the water level is too low. Stop the ice maker, add water to the reservoir, and then restart the appliance.
Why is my Ugur UBM 20 Ice Maker not making ice?
If your Ugur Ice Maker isn't making ice even though the cycle seems normal, the ambient or water temperature might be too high. Ensure the ambient temperature is below 32? and use cold water. If the issue persists, there may be a refrigerant leak or a blockage in the cooling system pipe, requiring assistance from a qualified technician.
How to stop ice cubes from sticking together in my Ugur UBM 20?
If you notice the ice cubes from your Ugur Ice Maker are sticking together, this could be due to a too long ice-making cycle or the water temperature being too low. Stop the ice maker, wait for the ice blocks to melt, and restart it, selecting the small ice size. Also, change the water in the reservoir to water between 5?-32?.
What does it mean when the 'Water' and 'Ice' indicators are flashing on my Ugur Ice Maker?
If the 'Water' and 'Ice' indicators are flashing on your Ugur Ice Maker, the ice shovel may be stuck. Check if ice is blocking the ice shovel. If there is no blockage, consult a certified technician.
Why are the ice cubes melting in my Ugur UBM 20 Ice Maker?
If the ice cubes in your Ugur Ice Maker are melting, this could be due to temperature changes in the appliance's location or frequent opening of the lid. Leaving ice in the appliance for too long can also cause it to recycle by melting and remaking the ice. Ensure the appliance is in a temperature-regulated area, avoid leaving the lid open, and transfer ready-made ice to a cooler or freezer.
What to do if the 'add water' indicator stays on my Ugur UBM 20 Ice Maker?
If the indicator to “add water” stays on even when there is enough water in the water tank of your Ugur Ice Maker, the water filter on the bottom of the water tank may be blocked. Remove and clean the water filter. If the issue continues, unplug the unit, wait 5-10 minutes, plug it back in, and follow the start-up procedure.
Why are the ice cube sizes inconsistent in my Ugur UBM 20 Ice Maker?
If the ice cube sizes are inconsistent in your Ugur Ice Maker, the ice case panel may not be level. Adjust the ice case panel to ensure it is level.
Why is the 'ice full' indicator on when there's not enough ice in my Ugur UBM 20 Ice Maker?
If there are not enough ice cubes in the ice basket, but the 'ice full' indicator is on for your Ugur Ice Maker, the room temperature may be too low (around 5?). The ice cubes formed may be touching the sensor. Ensure the unit is in an area where the temperature is above 5?. Remove the ice cubes and wait a few minutes for the unit to restart.
Panel that pushes already formed ice into the ice basket below.
Easy to use, visible functions and 1-touch display setting.
For draining water from the water reservoir.
With a transparent window to allow interior visibility.
Ice sensor determines when the ice basket is full.
Steps for removing packaging and initial setup of the ice maker.
Instructions for safely connecting the ice maker to a power source.
Procedures for cleaning the interior and exterior of the ice maker.
Step-by-step guide on how to operate the ice maker.
Addresses low water level or flashing water indicator.
Addresses full ice basket or flashing ice indicator.
Solutions for ice cubes sticking together or long ice making cycles.
Troubleshooting when no ice is made despite normal cycle.
Addresses issues related to low or high water/ambient temperatures.
Solutions for a leaking ice maker, possibly due to drainage cap.
Addresses ice melting due to appliance location or lid usage.
Addresses 'add water' indicator staying on due to blocked filter.
Solutions for inconsistent ice cube sizes.
Addresses 'ice full' indicator when ice basket is not full.
General| Brand | Ugur |
|---|---|
| Model | UBM 20 |
| Category | Ice Maker |
| Voltage | 220-240 V |
| Frequency | 50 Hz |
| Refrigerant | R134a |
| Ice Production Capacity | 20 kg/24 hours |
To Next Page
