EasyManua.ls Logo

UltraCOOL M201A - User Manual

Default Icon
11 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Circle the model of your cooler and
record the serial number below.
Read Carefully All Of This Manual
Before Installing The Unit.
Encierre con un circulo el modelo de su
enfriador y escribe el número de serie abajo.
Lea Con Cuidado Todo Este Manual Antes
De Instalar La Unidad.
Serial #
Número De Serie
Read And Save These Instructions
Evaporative Cooling
Evaporative cooling is nature’s way of cooling. When air is moved
over a wet surface, water is evaporated and heat is absorbed. When
stepping out of a swimming pool with the wind blowing, evaporative
cooling makes you feel cool, even though the air may be warm.
The human body itself is cooled primarily by the evaporation of
perspiration.
This unit works on the same principle. Air is drawn across wet
fi lter pads where the air is cooled by evaporation and then circulated
throughout the building. It is this combination of cooled air and the
movement of air over the skin which makes it feel cool.
Unlike refrigeration systems which recirculate the air, an evaporative
cooler continually brings in fresh air while exhausting old air. You
are completely replacing the air every 2 to 4 minutes by opening
windows or doors or a combination of both. The air is always fresh,
not stale, laden with smoke and odors as happens with refrigerated
air conditioning.
Vea el Español en el interior
110522-1 1-09www.championcooler.com
MOBILE EVAPORATIVE
COOLER
Manual Control Units
M201A
M301A
M401A
Remote Control Units
RM301A
RM401A
Safety Rules
1. Read these instructions carefully.
2. Unit must be in the Off Position and Unplugged from power
receptacle when installing or performing any maintenance.
3. This cooler will run on 120 volt A.C., 60 Hz (cycle) current
only.
4. Motor and pump are grounded and have an automatic thermal
overload switch which will shut motor off if it overheats. The
motor will restart automatically when it cools down.
5. Pump receptacle is for grounded evaporative cooler pump only.
Do not plug anything else into receptacle.
WARNING: To reduce the risk of fi re or electric shock, do not
use this fan with any “solid-state fan speed control device.”

Table of Contents

Other manuals for UltraCOOL M201A

Preview: User Guide
User Guide11 pages

Questions and Answers

  • S
    Stephanie AndersonAug 20, 2025
    What to do if my UltraCOOL Freezer fails to start?
    • B
      benjamin83Aug 20, 2025
      If your UltraCOOL Freezer fails to start or deliver air, there might be several reasons: * There could be no electrical power to the unit. Check the voltage. * A fuse might be blown. In this case, replace the fuse. * The circuit breaker may have tripped. Try resetting the breaker. * The electric cord could be unplugged or damaged. Ensure the cord is plugged in, and replace it if damaged. * You may need to adjust the belt tension. * You may need to oil or replace the bearings. * You may need to oil the bearings.
  • K
    Kevin PowellAug 22, 2025
    Why is my UltraCOOL Freezer so noisy?
    • S
      Sarah TorresAug 22, 2025
      If your UltraCOOL Freezer is noisy, the following could be the reasons: * The bearings may be dry. Try oiling the bearings. * The wheel might be rubbing against the blower housing. Inspect and realign it. * Some parts might be loose. Tighten any loose parts.
  • J
    Jacqueline ParkAug 25, 2025
    What to do if my UltraCOOL Freezer is not cooling properly?
    • B
      Barbara BlackAug 25, 2025
      If your UltraCOOL Freezer isn't cooling adequately, it might be due to: * Inadequate exhaust in the house. Open windows or doors to increase airflow. * Pads not being wet. Check the water distribution system.
  • T
    tcampbellAug 26, 2025
    Why is my UltraCOOL Freezer air delivery inadequate?
    • B
      Bob WilliamsAug 26, 2025
      If you're experiencing inadequate air delivery from your UltraCOOL Freezer while it's running, consider these potential causes: * Insufficient air exhaust. Open windows or doors to increase airflow. * A belt that is too loose. Adjust the belt tension or replace it if needed. * Pads that are plugged. Replace the pads.
  • G
    Gary PrattAug 27, 2025
    Why does my UltraCOOL Freezer motor cycle on and off?
    • P
      Peter NormanAug 28, 2025
      If your UltraCOOL Freezer motor cycles on and off, it could be due to several reasons: * Low voltage. Check the voltage. * Excessive belt tension. Adjust the belt tension. * Blower shaft tight or locked. * Bearings dry. Oil the bearings.
  • R
    Raymond CooperAug 30, 2025
    How to get rid of musty odor from UltraCOOL Freezer?
    • M
      Melvin ObrienAug 30, 2025
      If your UltraCOOL Freezer has a musty or unpleasant odor, it could be due to: * Stale or stagnant water in the cooler. Drain the pan and clean the pads. * Pads that are mildewed or clogged. Replace the pads. * Pads not wetting properly. Check the water distribution system.
  • A
    Amber GreenSep 1, 2025
    Why is my UltraCOOL Freezer causing excessive humidity?
    • E
      elewisSep 1, 2025
      If there's excessive humidity in your house when running the UltraCOOL Freezer, it could be due to inadequate exhaust. Try opening doors or windows to increase airflow.
  • S
    Shawn GrossSep 2, 2025
    What to do if UltraCOOL Freezer is draining water?
    • S
      sochoaSep 3, 2025
      If water is draining from your UltraCOOL Freezer, it could be due to: * A float arm not adjusted properly. Adjust the float. * The drain assembly leaking. Tighten the nut and drain cap.
  • A
    Antonio ThomasSep 5, 2025
    How to troubleshoot UltraCOOL M201A failure to start?
    • R
      rebeccabishopSep 5, 2025
      If your UltraCOOL Air Cleaner fails to start or deliver air, several factors could be at play. First, check if the unit is receiving electrical power by verifying the voltage. A blown fuse or tripped circuit breaker could also be the culprit; replace the fuse or reset the breaker as needed. Ensure the electric cord is properly plugged in and replace it if damaged. Additionally, inspect the belt tension; adjust if it's too loose or too tight. Overheating of the motor can also cause this issue, so determine the cause of overheating. For blower issues, oil the blower bearings if they're dry. In a worst-case scenario, the motor might be locked, necessitating a replacement.
  • F
    franklinericSep 6, 2025
    Why is my UltraCOOL M201A not delivering enough air?
    • D
      Daniel HallSep 7, 2025
      If your UltraCOOL Air Cleaner is running but not delivering enough air, the issue could stem from insufficient air exhaust. Try opening windows or doors to increase airflow. Also, check the belt tension; adjust it or replace the belt if needed. Finally, inspect the pads; if they're plugged, replace them to restore proper air delivery.

Summary

Safety Rules

Operation

Manual Control Units Operation

Details on using the rotary switch for pump and fan settings on manual units.

Remote Control Units Operation

Explains operation via front panel buttons and wireless remote control.

Cooler Installation

Installing Casters

Instructions for attaching swivel casters to the unit's bottom pan.

Connecting Water

Steps for installing the drain assembly and float valve for water supply.

Filling the Water Pan

Guidance on manually filling or attaching a hose for continuous water supply.

Maintenance

Annual Maintenance Tasks

Covers oiling bearings, checking belts, and cleaning the pump annually.

Routine Maintenance Tasks

Includes draining water weekly and proper unit storage procedures.

Limited Warranty

Troubleshooting

Specifications

Replacement Parts List

UltraCOOL M201A Specifications

General IconGeneral
ModelUltraCOOL M201A
CategoryAir Cleaner
Filter TypeHEPA
Number of Fan Speeds3
Weight15 lbs
Noise Level25 dB