EasyManua.ls Logo

ULTRAFRYER F-P20-18 - User Manual

ULTRAFRYER F-P20-18
60 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
30A168
ULTRAFRYER GAS FRYER
MODEL F-P20-18 / 20
OPERATION INSTRUCTIONS
302 Spencer Lane • P.O. Box 5369
(800) 525-8130 • (210) 731-5000 • Fax: (210) 731-5099
San Antonio, Texas 78201
www.ultrafryer.com
FOR YOUR SAFETY
Do not store or use gasoline or other ammable vapors or
liquids in the vicinity of this or other appliance.
WARNING
Improper Installation, adjustment, alteration, service, or main-
tenance can cause property damage, injury, or death. Read the
installation, operating, and maintenance instructions thoroughly
before installing or servicing this equipment.

Table of Contents

Questions and Answers

  • B
    Bradley LopezAug 12, 2025
    How to fix ULTRAFRYER F-P20-18 main burner not igniting?
    • S
      Samantha AliAug 12, 2025
      If your ULTRAFRYER Fryer's main burner won't ignite but the blower is running, and there's no gas at the burner, first, check the blower air pressure switch by temporarily disconnecting the two ORANGE air switch wires and connecting them together. If the ignitor sparks when these wires are connected, the air pressure switch is defective and needs replacement. Also, inspect the gas control valve, hi-limit switch, and transformer; replace any that are defective.
  • D
    Dillon ShortAug 16, 2025
    Why is the shortening temperature too high in my ULTRAFRYER F-P20-18 Fryer?
    • Z
      Zachary Gonzales DDSAug 16, 2025
      If the shortening temperature in your ULTRAFRYER Fryer is too high and breaks down quickly, verify the gas pressure as described in the manual. Additionally, check the calibration of the electronic thermostat using an accurate digital thermometer.
  • J
    Jeffrey SuttonAug 19, 2025
    What to do if ULTRAFRYER F-P20-18 blower is not operating?
    • A
      Alec TylerAug 19, 2025
      If your ULTRAFRYER Fryer's electrical power is on, but the blower isn't working, the blower may have overheated and shut off due to thermal overload. This should correct itself when the motor cools down, which usually takes 10-20 minutes. If the overheating continues, you should replace the blower motor.
  • E
    Emily JonesAug 23, 2025
    Why is my ULTRAFRYER F-P20-18 Fryer pump/motor running but not pumping shortening?
    • A
      Alexander JohnsonAug 23, 2025
      If your ULTRAFRYER Fryer pump/motor operates but doesn't pump shortening, check for congealed shortening in the shortening system. Also, inspect the standpipe/suction line coupler connection to ensure it is not loose.
  • B
    Brian CordovaAug 27, 2025
    What to do if filter pump motor won't operate on ULTRAFRYER Fryer?
    • A
      aacostaAug 27, 2025
      If the filter pump motor on your ULTRAFRYER Fryer won't operate when you place the Vat Shortening Return/Topside Shortening Lever in the OPEN position, ensure the filter pump micro-switch is working. Then, check the manual reset button on the filter pump motor. If the motor still doesn't operate after pressing the reset button, you may need to repair or replace the motor.
  • D
    David ArroyoAug 31, 2025
    Why does my ULTRAFRYER F-P20-18 pump/motor hum but not pump shortening?
    • C
      Cindy McintoshAug 31, 2025
      If your ULTRAFRYER Fryer pump/motor hums but won't pump shortening, check for congealed shortening in the pump or shortening plumbing.
  • J
    Justin JonesSep 4, 2025
    How to fix slow temperature recovery on ULTRAFRYER Fryer?
    • M
      Mark WalkerSep 4, 2025
      If it's taking too long to heat the shortening to cooking temperature in your ULTRAFRYER Fryer, and the burner flames seem small, make sure the manual gas valve is fully open. Also, check for obstructions in the gas line and flue pipe. Verify the orifice plug has the correct drill size opening as specified in the operational requirements chart, and inspect the blower fins for damage. Finally, use a manometer to check the gas pressure at the gas control valve pressure tap, comparing it to the operational requirements chart. If needed, adjust the pressure regulator (clockwise to increase, counter-clockwise to decrease), and replace the adjustment cover.
  • T
    Timothy FernandezSep 7, 2025
    Why is the shortening flow rate decreased while filtering in my ULTRAFRYER F-P20-18?
    • G
      gjohnsonSep 7, 2025
      If you notice a decreased shortening flow rate while filtering with your ULTRAFRYER Fryer, check for excessive sediment on the filter screen, standpipe suction fitting, or in the filter tub.

ULTRAFRYER F-P20-18 Specifications

General IconGeneral
BrandULTRAFRYER
ModelF-P20-18
CategoryFryer
LanguageEnglish