Need help?Do you have a question about the Uniden UBC370CLT and is the answer not in the manual?
Read and observe safety guidelines before using the scanner.
Unauthorized modifications may void operating authority.
Use correct impedance earphones to prevent hearing damage.
Unit is not waterproof; avoid exposure to rain or moisture.
Use POWER to turn off before disconnecting AC power to prevent memory corruption.
Details the frequency bands the scanner can monitor and their steps.
Highlights features like memory scanning, channel naming, and CTCSS/DCS.
Search and display CTCSS or DCS tone information.
Program the scanner using a PC connection.
Directly access stored frequencies using numeric keys.
Skip stored frequencies during scanning.
Provides radio broadcasts or tones as alarm sound with snooze.
Store and search up to 30 preset FM broadcast channels.
Designate channels for periodic checks during scanning.
Disables priority checks during reception.
Notifies if attempting to store an already programmed frequency.
Search for active frequencies within a defined range.
Skip non-favorite frequencies during searches.
Search preprogrammed service frequencies.
Details maximum scan and search speeds, including Turbo mode.
Scanner displays time; features alarm with snooze.
Configure a 2-second delay after transmissions.
Enable or disable the LCD backlight.
Confirms valid input and alerts to invalid entry with tones.
Uses non-volatile EEPROM for memory backup.
Alerts for low battery; provides clock backup.
Turns scanner off when battery power is too low.
Automatically turns scanner off after a preset time.
Identifies key buttons, knobs, and indicators on the scanner.
Adjusts audio output volume level.
Sets the signal level required to receive transmissions.
Initiates or resumes channel scanning.
Selects alarm sound (radio/tone) or disables it.
Silences alarm temporarily or controls LCD backlight.
Selects operation modes like Alarm Set, Clock Set, or Clock.
Temporarily stops scanning or sets auto-off timer.
Enters programming mode for frequencies and settings.
Used for frequency entry, channel selection, and programming.
Turns the scanner on and off; displays time in standby.
Cancels input, clears errors, or inputs decimal points.
Starts limit search or selects FM1 memory bank.
Locks/unlocks channels or selects FM2 memory bank.
Toggles delay option or selects FM3 memory bank.
Sets priority channels or selects memory recall mode.
Changes frequency step or selects direct entry mode.
Selects operating mode: FM, Service, or Scanner.
Navigate through channels, frequencies, and settings.
For firmware updates and PC programming.
Indicates the active channel memory bank (1-10).
Shows if a channel is locked out or skipped.
Displays when in Limit Search or Service Search modes.
Indicates when the scanner is in direct frequency entry mode.
Shows that the 2-second channel delay is active.
Indicates when the scanner is in programming mode.
Displays battery power level: full, low, or not installed.
Shows when scanning or searching is temporarily stopped.
Displays the current frequency step size (e.g., 25 kHz).
Shows AM/PM and operational modes like P (Priority) or M (Minute).
Indicates that a priority channel is active or in DND mode.
Shows when the alarm is enabled or sounding.
Notes on backlight auto-off and special tones for input feedback.
Tips for optimal performance: antenna placement, environment, and interference.
Instructions for connecting AC adapter and installing batteries.
Steps to set the scanner's current time and date.
Steps to configure the alarm clock time.
Tune directly to specific frequencies using keypad or navigation.
Save favorite FM stations for quick recall.
Search for active frequencies within a user-defined range.
Search pre-defined service frequency categories.
Set the upper and lower frequency limits for searching.
Start searching within the selected frequency range.
Temporarily pause the search at the current frequency.
How to perform a service search.
Choose from seven preset service frequency types.
Proper power handling, button operation, and memory care.
Advice on placement, interference, and environmental factors.
Instructions for safely cleaning the scanner exterior and display.
Lists supported frequency bands and their coverage.
Specifies the total number of channels and banks.
Details scan and search rates in channels/steps per second.
Accuracy of the scanner's clock function.
Details normal audio output power and internal speaker.
Specifies voltage, current, and battery requirements.
Details antenna type and available external connection ports.
Lists items provided with the scanner.
Specifies temperature ranges for operation and storage.
Provides size and weight of the scanner.
Provides contact details for sales, service, and support.
To Next Page
General
